ST72521R9 STMicroelectronics, ST72521R9 Datasheet - Page 122
ST72521R9
Manufacturer Part Number
ST72521R9
Description
8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, FIVE TIMERS, SPI, SCI, I2C, CAN INTERFACE
Manufacturer
STMicroelectronics
Datasheet
1.ST72521AR9.pdf
(215 pages)
Specifications of ST72521R9
Hdflash Endurance
100 cycles, data retention
Clock Sources
crystal/ceramic resonator oscillators, internal RC oscillator and bypass for external clock
Four Power Saving Modes
Halt, Active-Halt, Wait and Slow
Main Clock Controller With
Real time base, Beep and Clock-out capabilities
Two 16-bit Timers With
2 input captures, 2 output compares, external clock input on one timer, PWM and pulse generator modes
8-bit Pwm Auto-reload Timer With
2 input captures, 4 PWM outputs, output compare and time base interrupt, external clock with event detector
- Current page: 122 of 215
- Download datasheet (5Mb)
ST72F521, ST72521B
I
10.7.5 Low Power Modes
10.7.6 Interrupts
Figure 67. Event Flags and Interrupt Generation
Note: The I
the same interrupt vector (see Interrupts chapter).
They generate an interrupt if the corresponding
Enable Control Bit is set and the I-bit in the CC reg-
ister is reset (RIM instruction).
122/215
2
WAIT
HALT
10-bit Address Sent Event (Master mode)
End of Byte Transfer Event
Address Matched Event (Slave mode)
Start Bit Generation Event (Master mode)
Acknowledge Failure Event
Stop Detection Event (Slave mode)
Arbitration Lost Event (Multimaster configuration)
Bus Error Event
C BUS INTERFACE (Cont’d)
Mode
*
EVF can also be set by EV6 or an error from the SR2 register.
STOPF
ADD10
BERR
ARLO
ADSL
*
BTF
No effect on I
I
I
In HALT mode, the I
resumes operation when the MCU is woken up by an interrupt with “exit from HALT mode” capability.
2
2
SB
AF
2
C interrupts cause the device to exit from WAIT mode.
C registers are frozen.
C interrupt events are connected to
2
C interface.
Interrupt Event
2
C interface is inactive and does not acknowledge data on the bus. The I
ITE
Description
ADSEL
STOPF
ADD10
BERR
Event
ARLO
Flag
BTF
SB
AF
Control
Enable
ITE
Bit
INTERRUPT
EVF
from
Wait
Exit
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
2
C interface
from
Halt
Exit
No
No
No
No
No
No
No
No
Related parts for ST72521R9
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: