MAX9597CTI+T Maxim Integrated Products, MAX9597CTI+T Datasheet - Page 15

• Manufacturer Part Number: MAX9597CTI+T
• Description: IC AUD/VID INTERACE 28TQFN-EP
• Manufacturer: Maxim Integrated Products
• Type: Audio/Video Interfacer

Specifications of MAX9597CTI+T

• Applications: DVD, Set-Top Boxes
• Mounting Type: Surface Mount
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The video DAC outputs of the set-top box decoder chip
need to be lowpass-filtered to reject the out-of-band
noise. The MAX9597 integrates sixth-order, Butterworth
filters. The filter passband (±1dB) is typically 10MHz,
and the attenuation at 27MHz is 43dB. The filters are
suited for standard-definition video.
The video output amplifiers can both source and sink
load current, allowing output loads to be DC- or
AC-coupled. The amplifier output stage needs approxi-
mately 300mV of headroom from either supply rail.
If the supply voltage is greater than 3.135V (5% below
a 3.3V supply), each amplifier can drive two DC-cou-
pled video loads to ground. If the supply is less than
3.135V, each amplifier can drive only one DC-coupled
or AC-coupled video load.
The SCART standard allows for video signals to have a
superimposed DC component within 0V and 2V.
Therefore, most video signals are DC-coupled at the out-
put. In the unlikely event that the video signal needs to
be AC-coupled, the coupling capacitors should be
220µF or greater to keep the highpass filter formed by
the 37.5Ω equivalent resistance of the video transmis-
sion line to a corner frequency of 4.8Hz or below to keep
it well below the 25Hz frame rate of the PAL standard.
The video outputs can be enabled or disabled by bits 1
to 5 of register 0Dh. See Table 11.
Table 1. Recommended Coupling for Incoming Video Signals and Input Circuit
Configuration**
** Use a 0.1µF capacitor to AC-couple a video signal into the MAX9597.
VIDEO ORIGIN
External
External
External
External
Internal
Internal
Internal
Internal
Internal
Internal
Internal
Internal
______________________________________________________________________________________
FORMAT
Y, Pb, Pr
R, G, B
R, G, B
Video Reconstruction Filter
CVBS
CVBS
CVBS
RGB
Y, C
C
C
Y
Y
Low-Power Audio/Video Interface
Video Outputs
VOLTAGE RANGE
for Single SCART Connectors
Unknown
Unknown
Unknown
Unknown
2.3 to 3.3
2.3 to 3.3
2.3 to 3.3
2.3 to 3.3
0 to 1
0 to 1
0 to 1
0 to 1
(V)
The MAX9597 supports the IEC 933-1, Amendment 1,
trilevel slow-switching standard that selects the aspect
ratio for the display (TV). Under I
MAX9597 sets the slow-switching output voltage level.
Table 2 shows the valid input levels of the slow-switch-
ing signal and the corresponding operating modes of
the display device.
One port is available for slow-switching signals for the
TV. The slow-switching outputs can be set to a logic
level or high impedance by writing to bit 0 and 1 of reg-
ister 07h. See Table 9.
Table 2. Slow-Switching Modes
SLOW-SWITCHING
SIGNAL VOLTAGE
COUPLING
9.5 to 12.6
4.5 to 7.0
AC
AC
AC
AC
DC
DC
DC
DC
AC
AC
AC
AC
0 to 2
(V)
INPUT CIRCUIT CONFIGURATION
Display device uses an internal
source such as a built-in tuner to
provide a video signal.
Display device uses a video signal
from the SCART connector and sets
the display to a 16:9 aspect ratio.
Display device uses a signal from the
SCART connector and sets the
display to a 4:3 aspect ratio.
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Transparent sync-tip clamp
Bias circuit
Bias circuit
MODE
2
Slow Switching
C control, the
15