MAX4403 Maxim, MAX4403 Datasheet
![no-image](/images/no-image-200.jpg)
MAX4403
Available stocks
Related parts for MAX4403
MAX4403 Summary of contents
Page 1
... SC70 and space-saving 5-pin SOT23 packages. The single MAX4401 includes the shutdown feature and is available in a 6-pin SC70. The MAX4402 is a dual amplifier available in 8-pin SOT23 and SO packages. The MAX4403 quad amplifier is packaged in a 14-pin TSSOP or SO. Single-Supply, Zero-Crossing Detectors Instruments and Terminals ...
Page 2
... Lead Temperature (soldering, 10s) .................................+300°C = ∞ connected to V /2, SHDN = V / CONDITIONS Inferred from PSRR test 5.0V DD SHDN = V (Note 1) SS MAX4400/MAX4401 MAX4402/MAX4403 (Note 2) (Note 2) Differential or common mode Inferred from CMRR test ≤ V ≤ 1. 2.5V ≤ V ≤ 5. 0.3V ≤ 100kΩ V ...
Page 3
... step S OUT = ∞ connected to V / CONDITIONS Inferred from PSRR test MAX4400/MAX4401 OS MAX4402/MAX4403 VOS I (Note (Note 2) OS Inferred from CMRR test CM ≤ V ≤ 1. ≤ V ≤ 1. -20°C to +125°C ...
Page 4
Single/Dual/Quad, Low-Cost, Single-Supply, Rail-to-Rail Op Amps with Shutdown (V = +5V /2, V SHDN GAIN AND PHASE vs. FREQUENCY (NO LOAD -20 -40 -60 -80 ...
Page 5
Single/Dual/Quad, Low-Cost, Single-Supply, Rail-to-Rail Op Amps with Shutdown (V = +5V /2, V SHDN OUTPUT VOLTAGE SWING LOW vs. TEMPERATURE 2kΩ ...
Page 6
... NONINVERTING SMALL-SIGNAL TRANSIENT RESPONSE A = +1V 2kΩ 50mV/div OUT 2µs/div PERCENT OVERSHOOT vs. CAPACITIVE LOAD NEGATIVE OVERSHOOT POSITIVE OVERSHOOT 100 200 300 400 500 600 C (pF) LOAD MAX4402/MAX4403 CHANNEL-TO-CHANNEL ISOLATION vs. FREQUENCY 0 100 1000 FREQUENCY (kHz) ...
Page 7
... Detailed Description Rail-to-Rail Output Stage The MAX4400–MAX4403 can drive a 2kΩ load and still typically swing within 55mV of the supply rails. Figure 1 shows the output voltage swing of the MAX4400 config- ured with A = +10V/V. V Driving Capacitive Loads Driving a capacitive load can cause instability in many op amps, especially those with low quiescent current ...
Page 8
... OUT 1V/div OUT Figure 5. Power-Up/Power-Down Waveform The MAX4400–MAX4403 operate from a single +2.5V to +5.5V power supply. Bypass the power supply with a 0.1µF capacitor to ground. Good layout techniques optimize performance by decreasing the amount of stray capacitance at the op amp’s inputs and outputs. To decrease stray capaci- tance, minimize trace lengths by placing external com- ponents close to the op amp’ ...
Page 9
... Single/Dual/Quad, Low-Cost, Single-Supply, Rail-to-Rail Op Amps with Shutdown MAX4402 OUTA 1 INA- 2 INA SOT23-8/SO/µMAX _______________________________________________________________________________________ Pin Configurations (continued) MAX4403 OUTA 1 INA INA OUTB INB INB+ 5 INB+ INB OUTB TSSOP/SO Package Information 14 OUTD IND- ...
Page 10
Single/Dual/Quad, Low-Cost, Single-Supply, Rail-to-Rail Op Amps with Shutdown 10 ______________________________________________________________________________________ Package Information (continued) ...
Page 11
Single/Dual/Quad, Low-Cost, Single-Supply, Rail-to-Rail Op Amps with Shutdown ______________________________________________________________________________________ Package Information (continued) 11 ...
Page 12
... Single/Dual/Quad, Low-Cost, Single-Supply, Rail-to-Rail Op Amps with Shutdown Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...