MAX44260 Maxim, MAX44260 Datasheet
MAX44260
Available stocks
Related parts for MAX44260
MAX44260 Summary of contents
Page 1
... The family of parts operates from a supply range of 1.8V to 5.5V over the -40NC to +125NC temperature range and can operate down to 1.7V over the 0NC to +70NC tem- perature range. The MAX44260/MAX44261 are available in small, 6-pin SC70 packages. The MAX44260 is also available in a 1mm x 1.5mm thin μDFN (ultra-thin LGA) package. Ordering Information appears at end of data sheet ...
Page 2
... CMRR V = -0. 0.1V 0. 0.4V, R OUT DD 0. 0.4V OUT DD 0. 0.4V, R OUT MAX44260/MAX44261 = -40NC to +125NC. Typical values are SHDN DD A MIN TYP -0.1 10 0.8 0.01 0 10kI 100 115 OUT = 600I 91 100 OUT = 32I 80 OUT 50 ) ...
Page 3
... A O P-P V = 0.2V, V 3.3V OUT 20Ω 1nF (load Guaranteed by PSRR 0NC to +70NC A PSRR MAX44260/MAX44261 only I SHDN SHDN MAX44260 MAX44261 T = +25NC (Note SHDN T -40C to +125C (Note +25NC (Note -40 ...
Page 4
... T = -40° -40 - +125°C A -80 -100 -0.5 0 0.5 1.0 1.5 2.0 1.25 COMMON-MODE VOLTAGE (V) MAX44260/MAX44261 = -40NC to +125NC. Typical values are at SHDN +25NC. Temperature limits are guaranteed by design.) A INPUT 4.5 5.0 5.5 -15 - INPUT OFFSET VOLTAGE (µV) OUTPUT-VOLTAGE LOW vs. OUTPUT SINK CURRENT ...
Page 5
... T = +25°C A 120 100 +125° 100 0 OUTPUT SOURCE CURRENT (mA) MAX44260/MAX44261 = -40NC to +125NC. Typical values are at SHDN +25NC. Temperature limits are guaranteed by design.) A OUTPUT-VOLTAGE HIGH vs. OUTPUT SOURCE CURRENT ( 200 180 160 140 T = +25° ...
Page 6
... FREQUENCY (kHz) DC CMRR AND PSRR vs. TEMPERATURE -90 -92 DC CMRR -94 -96 -98 DC PSRR -100 100k -50 - TEMPERATURE (°C) MAX44260/MAX44261 = -40NC to +125NC. Typical values are at SHDN +25NC. Temperature limits are guaranteed by design.) A COMMON-MODE REJECTION RATIO vs. FREQUENCY 0 -20 -40 -60 -80 -100 -120 1k ...
Page 7
... SHDN +25NC. Temperature limits are guaranteed by design.) A TOTAL HARMONIC DISTORTION vs. INPUT AMPLITUDE (f = 10kHz 120 115 110 105 100 10k 100k 0 0.5 1.0 1.5 2.0 INPUT AMPLITUDE (V) LARGE-SIGNAL TRANSIENT RESPONSE MAX44260 toc23 INPUT 1V/div OUTPUT 500mV/div 5.5V 1V/V) V 2.5 3.0 3.5 4.0 4.5 5.0 MAX44260 toc24 100ns/div ...
Page 8
... STABLE UNSTABLE 100k 0 500 1000 1500 2000 2500 CAPACITIVE LOAD (pF) MAX44260 toc28 MAX44260/MAX44261 = -40NC to +125NC. Typical values are at SHDN +25NC. Temperature limits are guaranteed by design.) A STABILITY vs. CAPACITIVE AND RESISTIVE LOAD 100k 10k 1k UNSTABLE 100 STABLE ...
Page 9
... SS IN- Negative Input OUT Output CAL Active-Low Calibrate Input SHDN Active-Low Shutdown V Positive Power Supply. Bypass with a 0.1FF capacitor to ground. DD Pin Configurations V SHDN OUT CAL MAX44260 4 OUT IN+ V IN- SS Thin µDFN (Ultra-Thin LGA) Pin Description FUNCTION ...
Page 10
... The MAX44261 features a user-selectable self-calibration input that shuts down the device and allows reca- librated at any time. The calibration routine takes 10ms. Figure 1. Comparing the Input Structure of the MAX44260 to Standard Op-Amp Inputs Figure 2. Crossover Distortion of Typical Amplifiers ________________________________________________________________ Maxim Integrated Products 10 1 ...
Page 11
... The MAX44261 features a recalibrate input that acts the same as the shutdown mode of the MAX44260. However, when the input is pulled low, the device goes through a self-calibration sequence again The shutdown logic levels of the devices are indepen- dent of supply, allowing the shutdown feature of the device to operate off ...
Page 12
... This makes these devices ideal for ground-referenced medical and industrial sensor applications. The MAX44260/MAX44261 are ideal for a wide variety of active filter circuits that make use of their wide band- width, rail-to-rail input/output stages and high-impedance CMOS inputs ...
Page 13
... RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE 6 SC70 6 Thin FDFN (Ultra-Thin LGA) ________________________________________________________________ Maxim Integrated Products 13 1.8V 15MHz Low-Offset, Low-Power, Rail-to-Rail I/O Op Amps PACKAGE CODE X6SN+1 Y61A1+1 MAX44260/MAX44261 Package Information OUTLINE NO. LAND PATTERN NO. 21-0077 21-0190 90-0189 90-0233 ...
Page 14
... For the latest package outline information and land patterns (footprints www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. ________________________________________________________________ Maxim Integrated Products 14 1.8V 15MHz Low-Offset, Low-Power, Rail-to-Rail I/O Op Amps Package Information (continued) MAX44260/MAX44261 ...
Page 15
... For the latest package outline information and land patterns (footprints www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. ________________________________________________________________ Maxim Integrated Products 15 1.8V 15MHz Low-Offset, Low-Power, Rail-to-Rail I/O Op Amps Package Information (continued) MAX44260/MAX44261 ...
Page 16
... Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2012 Maxim Integrated Products MAX44260/MAX44261 1.8V 15MHz Low-Offset, DESCRIPTION Maxim is a registered trademark of Maxim Integrated Products, Inc. ...