MAX907 Maxim, MAX907 Datasheet
MAX907
Available stocks
Related parts for MAX907
MAX907 Summary of contents
Page 1
... Not Recommended for New Designs The MAX909 was manufactured for Maxim by an outside wafer foundry using a process that is no longer available not recommended for new designs. A Maxim replacement or an industry second-source may be available. The data sheet remains available for existing users. ...
Page 2
... The MAX909 features complementary outputs and an output latch. A separate supply pin for extending the analog input range down to -5V is also provided. The dual MAX907 and single MAX909 are available in 8-pin DIP and SO packages, and the quad MAX908 is available in 14-pin DIP and SO packages. These com- ...
Page 3
... Plastic DIP (derate 10.00mW/°C above +70° 800mW 14-Pin SO (derate 8.33mW/°C above +70° 667mW Operating Temperature Ranges: MAX90_C_ 0°C to +70°C MAX90_E_ -40°C to +85°C MAX907MSA/ -55°C to +125°C Storage Temperature Range . . . . . . . . . . . . . . . . . . . -65°C to +150°C Lead Temperature (soldering, 10s +300°C = 0V; unless otherwise noted.) LATCH ...
Page 4
... CMRR (Notes 4, 5) PSRR (Notes 100µA SOURCE = 3.2mA T MIN = OL SINK T MIN = - MAX907/MAX908 I+ (Note 7) MAX909 I- MAX909 only -5V MAX907/MAX908 PD (Note 8) MAX909 MIN TYP MAX 2.0 0 MIN TYP MAX 200 50 -0 1.5 -5 1.5 -0 ...
Page 5
... DC parameters are within the specified limits. V For the MAX909, propagation delay is typical only and there is no guaranteed maximum limit. Note 10: Differential Propagation Delay is specified as the difference between any two channels in the MAX907/MAX908 (both out- puts making either a low-to-high or a high-to-low transition). ...
Page 6
... SOURCE IMPEDANCE (Ω) OUTPUT HIGH VOLTAGE vs. SOURCE CURRENT 5 100mV IN 4 +125° +25° -55°C A 3.5 3.0 140 1 10 100 I (µA) SOURCE MAX907 TOTAL POSITIVE SUPPLY CURRENT vs. POSITIVE SUPPLY VOLTAGE (OUTPUTS 2 +125° +25° -55°C 1 ...
Page 7
Dual/Quad/Single, High-Speed, Ultra-Low-Power, Single-Supply TTL Comparators ( +25°C, unless otherwise noted.) A MAX908 TOTAL POSITIVE SUPPLY CURRENT vs. POSITIVE SUPPLY VOLTAGE (OUTPUTS 4 +125° +25°C A ...
Page 8
... MAX907/MAX908 PROPAGATION DELAY ( (5mV OVERDRIVE) MAX907 TOC20 INPUT GND -5mV OVERDRIVE OUTPUT 500mV/div TTL THRESHOLD (1.4V) OUTPUT GND 10ns/div MAX909 PROPAGATION DELAY ( (5mV OVERDRIVE) MAX907 TOC22 INPUT GND -5mV OVERDRIVE QOUT 1V/div 1.4V QOUT SKEW PD PD 10ns/div 1V/div GND 7 ...
Page 9
... Noise or undesired parasitic AC feedback cause most high-speed comparators to oscillate in the linear region (i.e., when the voltage on one input near the voltage on the other input). The MAX907/MAX908/ MAX909 eliminate this problem by incorporating inter- nal hysteresis. When the two comparator input voltages are equal, hysteresis effectively causes one comparator input voltage to move quickly past the other, thus taking the input out of the region where oscillation occurs ...
Page 10
... MAX403 converts the photodiode current to a voltage, and the MAX907 determines whether the amplifier output is high enough to be called a “1”. The current consump- tion of this circuit is minimal: The MAX403 and MAX907 require typically 250µA and 700µA, respectively. LATCH 3V 1 ...
Page 11
... MAX908CPD MAX908CSD 8 QOUT MAX908EPD QOUT 7 MAX908ESD MAX909CPA GND 6 MAX909CSA 5 LE MAX909EPA MAX909ESA MAX907 TRANSISTOR COUNT: 262 MAX908 TRANSISTOR COUNT: 536 MAX909 TRANSISTOR COUNT: 140 PROCESS: Bipolar Printed USA is a registered trademark of Maxim Integrated Products, Inc. 10pF 1MΩ +5V +5V 0.1µF MAX403 ...