MAX909 Maxim, MAX909 Datasheet
MAX909
Available stocks
Related parts for MAX909
MAX909 Summary of contents
Page 1
... Not Recommended for New Designs The MAX909 was manufactured for Maxim by an outside wafer foundry using a process that is no longer available not recommended for new designs. A Maxim replacement or an industry second-source may be available. The data sheet remains available for existing users. ...
Page 2
... The wide input common- mode range extends from 200mV below ground (below the negative supply rail for the MAX909) to within 1.5V of the positive supply rail. Because they are micropower, high-speed compara- tors that operate from a single +5V supply and include built-in hysteresis, these devices replace a variety of older comparators in a wide range of applications ...
Page 3
... MAX909 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (V- - 0.3V) to (V+ + 0.3V) Common-Mode Input Voltage MAX907/MAX908 . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V+ + 0.3V) MAX909 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (V- - 0.3V) to (V+ + 0.3V) Latch Input Voltage (MAX909 only -0.3V to (V+ + 0.3V) Input/Output Short-Circuit Duration GND . . . Continuous Stresses beyond those listed under “Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied ...
Page 4
... Dual/Quad/Single, High-Speed, Ultra-Low-Power, ELECTRICAL CHARACTERISTICS (continued) ( +25°C; MAX909 only 0V PARAMETER Propagation Delay Differential Propagation Delay Propagation Delay Skew Latch Input Voltage High Latch Input Voltage Low Latch Input Current Latch Setup Time Latch Hold Time ELECTRICAL CHARACTERISTICS ...
Page 5
... Note also that either or both inputs can be driven to the upper or lower absolute maximum limit with- CMR out damage to the part. Note 4: Tested with V+ = 5.5V (and for MAX909). MAX909 also tested over the full analog input range (i.e., with V- = -5.5V). Note 5: Tested over the full input voltage range (V Note 6: Specified over the full tolerance of operating supply voltage: MAX907/MAX908 tested with 4.5V < ...
Page 6
Dual/Quad/Single, High-Speed, Ultra-Low-Power, ( +25°C, unless otherwise noted.) A PROPAGATION DELAY vs. INPUT OVERDRIVE 10Ω 15pF LOAD INPUT ...
Page 7
... INPUT BIAS CURRENT vs. TEMPERATURE 300 200 100 -60 -40 - 100 120 140 TEMPERATURE (°C) MAX909 NEGATIVE SUPPLY CURRENT vs. NEGATIVE SUPPLY VOLTAGE 200 +125°C A 100 T = +25° -55° (V) SHORT-CIRCUIT OUTPUT CURRENT vs ...
Page 8
... MAX907/MAX908 PROPAGATION DELAY ( (5mV OVERDRIVE) MAX907 TOC20 INPUT GND -5mV OVERDRIVE OUTPUT 500mV/div TTL THRESHOLD (1.4V) OUTPUT GND 10ns/div MAX909 PROPAGATION DELAY ( (5mV OVERDRIVE) MAX907 TOC22 INPUT GND -5mV OVERDRIVE QOUT 1V/div 1.4V QOUT SKEW PD PD 10ns/div 1V/div ...
Page 9
... The state of the com- parator output is stored when LE is high (Figure 2). Note that the MAX909 can be operated with V- con- nected to ground negative supply voltage. The MAX909’s input range extends from (V- - 0.2V ...
Page 10
... Solder the device directly to the printed circuit board instead of using a socket. Overdriving the Inputs The inputs to the MAX907/MAX908/MAX909 may be driven beyond the voltage limits given in the Absolute Maximum Ratings, as long as the current flowing into the device is limited to 25mA. However, if the inputs are overdriven, the output may be inverted ...
Page 11
... QOUT MAX908EPD QOUT 7 MAX908ESD MAX909CPA GND 6 MAX909CSA 5 LE MAX909EPA MAX909ESA MAX907 TRANSISTOR COUNT: 262 MAX908 TRANSISTOR COUNT: 536 MAX909 TRANSISTOR COUNT: 140 PROCESS: Bipolar Printed USA is a registered trademark of Maxim Integrated Products, Inc. 10pF 1MΩ +5V +5V 0.1µF MAX403 ...