MAX9041 Maxim, MAX9041 Datasheet - Page 2

• Manufacturer Part Number: MAX9041
• Description: The MAX9039–MAX9043 and MAX9050–MAX9053 feature combinations of low-power comparators and precision voltage references
• Manufacturer: Maxim

ABSOLUTE MAXIMUM RATINGS
Supply Voltage (V
All Other Pins ...................................(V
Current into Input Pins ......................................................±20mA
Output Short-Circuit Duration
Continuous Power Dissipation (T
Micropower, Single-Supply, UCSP/SOT23
Comparator + Precision Reference ICs
ELECTRICAL CHARACTERISTICS—A Grade (0.4% Initial Accuracy)
(V
T
Note 1: This device is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the device
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
µMAX is a registered trademark of Maxim Integrated Products, Inc.
2
A
Supply Voltage Range (Note 3)
Supply Current
COMPARATORS
Input Offset Voltage (Note 4)
Input Hysteresis
Input Bias Current
(Notes 5, 6, 7)
Input Offset Current (Note 5)
Common-Mode Voltage Range
(Notes 5, 8)
Common-Mode Rejection Ratio
(Note 5)
Power-Supply Rejection Ratio
Input Capacitance (Note 5)
Output Short-Circuit Current
Output Voltage Low
CC
(OUT_, REF) ...............Indefinite Short Circuit to Either Supply
5-Pin SOT23 (derate 7.10mW/°C above +70°C)..........571mW
6-Bump UCSP (derate 3.9mW/°C above +70°C) ........308mW
6-Pin SOT23 (derate 8.70mW/°C above +70°C)..........696mW
= +25°C.) (Note 2)
_______________________________________________________________________________________
= +5V, V
can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder profiles recom-
mended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and Convection Packaging
Reflow. Preheating is required. Hand or wave soldering is not allowed.
PARAMETER
EE
CC
= 0V, V
to V
EE
CM
) ....................................-0.3V to +6V
= 0V, I
A
= +70°C)
SYMBOL
EE
CMVR
CMRR
V
PSRR
OUT
V
V
V
I
HYST
C
I
I
CC
I
OS
SC
- 0.3V) to (V
CC
OS
OL
B
IN
= 0A, I
MAX9040–MAX9043
MAX9050–MAX9053
MAX9040/MAX9041/
MAX9050/MAX9051
MAX9042/MAX9043/
MAX9052/MAX9053
Over entire
common-mode
range
Specified common-mode range
Specified common-mode range
T
T
Specified common-mode range
MAX9040–MAX9043, 2.5V ≤ V
MAX9050–MAX9053, 2.5V ≤ V
V
V
V
A
A
OUT
CC
CC
REF
= +25°C
= -40°C to +85°C
CC
= 5V, I
= 2.7V, I
= V
+ 0.3V)
= 0A, T
EE
SINK
or V
SINK
A
CONDITIONS
CC
= 8mA
= T
= 3.5mA
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Reflow Temperature (Note 1) ................................+235°C
MIN
T
T
A
A
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin µMAX
10-Pin µMAX (derate 5.6mW/°C above +70°C) ...........444mW
= +25°C
= -40°C to +85°C
V
V
to T
CC
CC
V
V
V
V
MAX
CC
CC
CC
CC
CC
CC
= 5V
= 2.7V
= 2.7V
= 5V
= 2.7V
= 5V
≤ 5.5V
≤ 5.5V
, unless otherwise noted. Typical values are at
®
(derate 4.1mW/°C above +70°C) ...........330mW
MIN
V
0.25
V
2.5
2.7
EE
52
55
55
EE
-
±0.001
TYP
0.15
±0.5
±3.0
±0.5
2.5
0.2
80
80
95
35
47
52
55
60
80
MAX
V
±10.0
±5.0
±7.0
0.25
0.55
V
CC
5.5
5.5
0.4
67
72
80
85
CC
+
UNITS
mV
mV
mA
µA
nA
pA
dB
dB
pF
V
V
V