MAX14506 Maxim, MAX14506 Datasheet
MAX14506
Related parts for MAX14506
MAX14506 Summary of contents
Page 1
... AC-coupling capaci- tance at the normally open (NO) terminals. This reduces click-and-pop sounds that occur when switching audio signals between precharged points. The MAX14504/ MAX14505/MAX14505A/MAX14506 control the switches with control bit, CB, and feature an enable input, EN, that place COM in a high-impedance mode. The MAX14504/MAX14505/MAX14505A/MAX14506 are fully specified to operate from a single +2 ...
Page 2
... Storage Temperature Range .............................-65°C to +150°C CC Package Junction-to-Ambient Thermal Resistance (θ Lead Temperature (soldering) .........................................+300°C are clamped by internal diodes. For EN ≥ are clamped by internal diodes (MAX14505A/MAX14506). Limit forward-diode current 3.3nF, unless otherwise noted. Typical values are at V NEG CONDITIONS ...
Page 3
... Input Logic-High Input Logic-Low Input Leakage Current _______________________________________________________________________________________ with ± 3.3nF, unless otherwise noted. Typical values are at V NEG CONDITIONS V = +3.0V, switch open -2.5V, +2.5V; NO_ V = +2.5V, -2.5V, unconnected COM_ _ , (MAX14504/MAX14506 +3.0V, switch open -2.5V, +2.5V; NC_ V = +2.5V, -2.5V, unconnected COM_ 3. tch cl osed ; 2.5V , unconnected ...
Page 4
... CC CC (MAX14504/MAX14505 +5.5V (MAX14504/MAX14505 +3.0V (MAX14505A/MAX14506 +5.5V (MAX14505A/MAX14506 5.5V 0. 3.3nF NEG NEG = +85°C, and guaranteed by design over the specified temperature range )], V = output NO_ NC_ COM_ NO_ Typical Operating Characteristics ON-RESISTANCE vs ...
Page 5
Dual SPDT Negative Rail Analog Switches (V = 3.0V +25°C, unless otherwise noted FLATNESS vs 0.3650 0.3645 0.3640 0.3635 0.3630 - NC_/NO_ TURN-ON/TURN-OFF TIME vs. TEMPERATURE ...
Page 6
Dual SPDT Negative Rail Analog Switches with ±V Capability 3.0V +25°C, unless otherwise noted COM_ ON-LEAKAGE CURRENT vs. TEMPERATURE 2.5V COM_ UNCONNECTED NC_ NO_ ...
Page 7
... COM1 V CC MAX14504/ MAX14505/ MAX14505A/ NC1 MAX14506 NO1* 50Ω NEG GND C NEG MEASUREMENTS ARE STANDARDIZED AGAINST SHORTS AT IC TERMINALS. OFF-ISOLATION IS MEASURED BETWEEN COM_ AND OFF. NO_ OR NC_ TERMINAL ON EACH CROSSTALK IS MEASURED FROM ONE CHANNEL TO THE OTHER CHANNEL. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. ...
Page 8
... Analog Switch 1, Normally Open Terminal B1 COM2 Analog Switch 2, Common Terminal Active-Low Enable Input. Drive EN high to put switches in a high-impedance mode. Shunt click/pop EN switches are not affected by the state of EN. The MAX14505A/MAX14506 enter a low current state B2 when EN is driven high. B3, C3 GND Ground ...
Page 9
... OFF X = DON'T CARE. _______________________________________________________________________________________ with ±V impedance mode. When MAX14505 terminals have a signal range The MAX14505A/MAX14506 terminals have a sig- CC nal range ture a low supply current when The MAX14505/MAX14505A have internal shunt switch- to pass through both NO1 and NO2 terminals to suppress click- and-pop sounds that can occur when switching audio signals between precharged points ...
Page 10
... Dual SPDT Negative Rail Analog Switches with ±V Capability CC Digital Control Inputs The MAX14504/MAX14505/MAX14505A/MAX14506 logic inputs accept up to +5.5V, regardless of supply voltage. For example, with a +3.3V supply, CB and EN can be driven low to GND and high to +5.5V, allowing for mixed logic levels in a system. Using logic levels of ≥ ...
Page 11
... AUDIO AMPLIFIER MAX9722 DirectDrive ® AMPLIFIER AUDIO AMPLIFIER Chip Information PROCESS: CMOS DirectDrive is a registered trademark of Maxim Integrated Products, Inc. ______________________________________________________________________________________ with ±V Typical Operating Circuit V CC 0.1µF MAX14504/MAX14506 NC1 COM1 NC2 COM2 NO1 NO2 NEG C NEG GND 0.1µF ...
Page 12
... Changed Pin Configuration and Pin Description sections Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...