MAX318 Maxim, MAX318 Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
MAX318
Manufacturer Part Number
MAX318
Description
The MAX317/MAX318/MAX319 are precision, CMOS, monolithic analog switches
Manufacturer
Maxim
Datasheet
1.MAX317.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX3180EEUK+T
Manufacturer:
Maxim
Quantity:
1 396
Company:
Part Number:
MAX3180EUK+T
Manufacturer:
MAXIM
Quantity:
2 000
Part Number:
MAX3180EUK+T
Manufacturer:
MAXIX
Quantity:
20 000
Company:
Part Number:
MAX3181EEUK+T
Manufacturer:
TOSH
Quantity:
5 897
Part Number:
MAX3181EEUK+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX3181EUK+T
Manufacturer:
MAXIM
Quantity:
52
Part Number:
MAX3181EUK+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX31826MUA+
Manufacturer:
AOS
Quantity:
10 710
Part Number:
MAX3183EUK-T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX31855KASA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Precision, CMOS Analog Switches
The main limitation of supply voltages other than ±15V
is analog signal range reduction. The MAX317/
MAX318/MAX319 switches operate with bipolar sup-
plies of ±5V to ±20V. Typical Operating Characteristics
graphs show typical on resistance for ±15V, ±10V, and
±5V supplies. Switching times increase by a factor of
two
MAX317/MAX318/MAX319 can operate from unipolar
supplies of +10V to +30V. Both parts can also operate
from unbalanced supplies such as +24V and -5V.
Connect V- to 0V when operating with a single supply.
This means that VL must be connected to +5V to be
TTL compatible, or to V+ for CMOS logic input levels.
Proper power-supply sequencing is recommended for
all CMOS devices. It is important not to exceed the
absolute maximum ratings because stresses beyond
the listed ratings may cause permanent damage to the
devices. Always sequence V+ on first, followed by VL,
V-, and logic inputs. If power-supply sequencing is not
possible, protect the devices from overvoltage by
6
__________Applications Information
MAX317
_______________________________________________________________________Pin Description
_______________________________________________________________________________________
—
—
1
2
3
4
5
6
7
8
or
more
MAX318
Operation with Supply Voltages
PIN
—
—
1
2
3
4
5
6
7
8
for
MAX319
operation
—
—
Overvoltage Protection
1
8
3
4
5
6
7
2
NAME
Other Than ±15V
COM
GND
N.C.
NO
NC
NO
V+
VL
IN
V-
at
Analog-switch common terminal
No connect — not internally connected
Analog-switch normally open terminal
Logic ground
Analog-signal positive supply input
Logic-level positive supply input
Logic-level input
Analog-signal negative supply input
Analog-switch normally closed terminal
Analog-switch normally open terminal
±5V.
The
adding two small signal diodes in series with the sup-
ply pins (Figure 1). Adding the diodes reduces the
analog signal range to 1V below V+ and 1V below V-,
but low switch resistance and low leakage characteris-
tics are unaffected. Device operation is unchanged,
and the difference between V+ to V- should not exceed
+44V.
Figure 1. Overvoltage Protection Using Blocking Diodes
V g
FUNCTION
NO_
V+
V-
V+
V-
COM_