MAX364 Maxim, MAX364 Datasheet
MAX364
Available stocks
Related parts for MAX364
MAX364 Summary of contents
Page 1
... The MAX364/MAX365 are fabricated with Maxim’s new improved 44V silicon-gate process. Design improve- ments guarantee extremely low charge injection (10pC), low power consumption (35µ ...
Page 2
... Note 1: All leads are soldered or welded to PC board. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS— ...
Page 3
... Logic Supply Current 16.5V -16.5V All channels on or off, Ground Current I V GND 16.5V -16.5V DYNAMIC Turn-On Time MAX364, V Figure 2 Turn-Off Time t OFF MAX365, V Figure Charge Injection Q R GEN R L Off Isolation (Note 5) OIRR f = 1MHz, Figure 50Ω 5pF, ...
Page 4
... Charge Injection Q R GEN Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: On resistance match between channels and flatness are guaranteed only with bipolar-supply operation. ...
Page 5
Precision, Quad, SPST Analog Switches __________________________________________Typical Operating Characteristics (T = +25°C, unless otherwise noted LEAKAGE CURRENTS 2 I S(ON D(ON +125° +85° 15V V- = ...
Page 6
... V+ = 12V 1nF 0 - NAME IN1–N4 Logic Control Input Analog-Switch Common Terminal COM1–COM4 NC (normally closed, MAX364) NC1–NC4 NO (normally closed, MAX365) or Analog-Switch Terminal NO1–NO4 V- Negative-Supply Voltage Input Ground GND V Logic-Supply Voltage Input L V+ Positive-Supply Voltage Input—Connected to Substrate PAD Exposed Pad ...
Page 7
... Operation with Supply Voltages Other than ±15V The main limitation of supply voltages other than ±15V is reduction in the analog signal range. The MAX364/MAX365 switches operate with ±5V to ±20V bipolar supplies. The Typical Operating Characteristics graphs show typical on resistance for ±15V, ±10V, and ±5V supplies. Switching times increase by a factor of two or more for ± ...
Page 8
... COM_ IN1 IN_ GND LOGIC INPUT +3V 0.8V O REPEAT TEST FOR CHANNELS 2, 3, AND 4. FOR LOAD CONDITIONS, SEE SPECIFICATIONS. C INCLUDES FIXTURE AND STRAY CAPACITANCE IN_ OFF C MAX364 L OFF = +3V IN_ MAX365 +15V V+ VL NO_ OR NC_ -15V ...
Page 9
Precision, Quad, SPST Analog Switches _________________________________Test Circuits/Timing Diagrams (continued) FREQUENCY TESTED 100Hz to 13MHz +15V +5V C SIGNAL V+ VL GENERATOR 10dBm COM_ GEN IN_ NC_ OR NO_ ANALYZER GND -15V Figure 4. Off ...
Page 10
... Precision, Quad, SPST Analog Switches Pin Configurations/Functional Diagrams (continued) ______ NC1 MAX364 GND 3 NC4 THIN QFN 10 ______________________________________________________________________________________ NC2 NO1 GND NC3 NO4 NO2 11 V+ MAX365 NO3 ...
Page 11
... Precision, Quad, SPST Analog Switches (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ Package Information 11 ...
Page 12
... Precision, Quad, SPST Analog Switches (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages TOP VIEW FRONT VIEW 12 ______________________________________________________________________________________ Package Information (continued) DIM ...
Page 13
... NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY. -DRAWING NOT TO SCALE- Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...