MAX4537 Maxim, MAX4537 Datasheet
MAX4537
Available stocks
Related parts for MAX4537
MAX4537 Summary of contents
Page 1
... They are pin compatible with the industry-standard 74HC4316. The MAX4536 has four normally open (NO) switches, and the MAX4537 has four normally closed (NC) switches. The MAX4538 has two NO switches and two NC switches. These switches operate from a +2V to +12V single supply, or from ± ...
Page 2
... Note 2: All leads are soldered or welded to PC boards. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS— ...
Page 3
SPST Analog Switches with Enable ELECTRICAL CHARACTERISTICS—±5V Dual Supplies (continued) (V+ = 4.5V to 5.5V -4.5V to -5.5V, V values are +25°C.) A PARAMETER SWITCH DYNAMIC CHARACTERISTICS Turn-On Time Turn-Off Time Break-Before-Make Time Delay (MAX4538 ...
Page 4
Quad, Low-Voltage, SPST Analog Switches with Enable ELECTRICAL CHARACTERISTICS—+5V Single Supply (V+ = 4.5V to 5.5V 0V 2.4V, V INH values are +25°C.) A PARAMETER SYMBOL ANALOG SWITCH V Analog Signal Range V ...
Page 5
... Note 5: ∆R = ∆R - ∆R ON ON(MAX) ON(MIN) Note 6: Resistance flatness is defined as the difference between the maximum and the minimum value of on-resistance as measured over the specified analog-signal range. Note 7: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation +25°C. A ...
Page 6
Quad, Low-Voltage, SPST Analog Switches with Enable __________________________________________Typical Operating Characteristics (V+ = +5V -5V GND = 0V +25°C, unless otherwise noted.) A ON-RESISTANCE vs. V COM (DUAL SUPPLIES) 200 180 160 V± = ±1.5V 140 120 ...
Page 7
SPST Analog Switches with Enable _____________________________Typical Operating Characteristics (continued) (V+ = +5V -5V GND = 0V +25°C, unless otherwise noted.) A FREQUENCY RESPONSE MAX4536/7/8 TOC-10 0 -10 ON-RESPONSE -20 -30 -40 ON-PHASE -50 -60 -70 -80 ...
Page 8
... This voltage can damage the MAX4536/MAX4537/MAX4538. Even ±5% tolerance supplies may have overshoot or noise spikes that exceed 13.0V. The MAX4536/MAX4537/MAX4538 operate from single supplies between +2.0V and +12V when V- is connect GND. All of the bipolar precautions must be observed. ...
Page 9
... MAX4538 V+ NO1 COM1 V = +3V COM1 COM2 N02 V = +3V COM2 IN LOGIC GND V- INPUT V- C INCLUDES FIXTURE AND STRAY CAPACITANCE. L Figure 2. Break-Before-Make Interval (MAX4538 only) MAX4536 MAX4537 MAX4538 R GEN COM V GEN GND IN Figure 3. Charge Injection _______________________________________________________________________________________ SWITCH LOGIC OUTPUT NO INPUT V OUT ...
Page 10
... Figure 5. Crosstalk MAX4536 MAX4537 MAX4538 CAPACITANCE METER 2. 1MHz V- 10nF V- Figure 7. Channel-On Capacitance MAX4536 V+ 10nF MAX4537 MAX4538 V+ N01 COM1 IN2 IN1 COM2 N02 GND V- 10nF MAX4536 10nF MAX4537 MAX4538 V+ COM 10nF GND 2. 2.4V ...
Page 11
... MAX4537CPE 0°C to +70°C MAX4537CSE 0°C to +70°C MAX4537CEE 0°C to +70°C MAX4537C/D 0°C to +70°C MAX4537EPE -40°C to +85°C MAX4537ESE -40°C to +85°C MAX4537EEE -40°C to +85°C MAX4538CPE 0°C to +70°C MAX4538CSE 0°C to +70°C MAX4538CEE 0°C to +70°C MAX4538C/D 0° ...
Page 12
... B E Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied ...