TSG12832L TEAM SOURCE DISPLAY, TSG12832L Datasheet
TSG12832L
Specifications of TSG12832L
Related parts for TSG12832L
TSG12832L Summary of contents
Page 1
... Product Specification For Customer： Module No.： TSG12832L-25 For Customer’s Acceptance ： Approved by Team Source Display Presented by ---------------------------------------------------------------------------------------------------------------------------- LCD Module □：APPROVAL FOR SPECIFICATION □：APPROVAL FOR SAMPLE Comment ： Reviewed by Organized by ...
Page 2
... Team Source Display Table of Content 1. Basic Specifications……………….………………………………………………3 Display Specifications………………………..……………………………………………………………….3 1.1 1.2 Mechanical Specifications… ...
Page 3
... Team Source Display 1. Basic Specifications 1.1 Display Specifications 1>LCD Display Mode 2>Viewing Angle 3>Driving Method 4>Backlight 1.2 Mechanical Specifications 1>Outline Dimension 1.3 Circuit Diagram VDD VSS /CS1,A0,R/W,E,/RST DB0~DB7 www.tslcd.com : FSTN, Positive, Reflective : 6H : 1/33 Duty, 1/6 Bias : NC : 35.0 x 17.9 x 1.8mm (See attached Outline Drawing for Page14) LCD Panel 128 x 32 Pixels … ...
Page 4
... Team Source Display 1.4 Terminal Function Pin No. Pin Name VDD 1 P/S 2 VSS CAP2+ 9 CAP2- 10 CAP1- 11 CAP1+ 12 CAP3- 13 VOUT 14 VSS2 15 DB7~DB0 16~ /RES 27 /CS 28 www.tslcd.com Function Power supply voltage (Positive Negative power supply,0V This is a multi-level power supply for the liquid crystal drive. ...
Page 5
... Team Source Display 2. Absolute Maximum Ratings Items Symbol Supply Voltage Input Voltage Operating Temperature Storage Temperature 3. Electrical Characteristics 3.1 DC Characteristics Items Symbol Operating Voltage V Input High Voltage V Input Low Voltage V Output High Voltage V Output Low Voltage V Input Leakage Current I Output Leakage Current ...
Page 6
... Team Source Display 3.3 AC Characteristics 3.3.1 8080 Mode System Bus Timing Items System cycle time Address setup time(A0) Address hold time(A0) Control Low Pulse wide(/RD) Control Low Pulse wide(/WR) Control High Pulse wide(/RD) Control High Pulse wide(/WR) Data steup time Data hold time ...
Page 7
... Team Source Display 3.3.2 Items System cycle time Address setup time(A0) Address hold time(A0) Control Low Pulse wide(/RD) Control Low Pulse wide(/WR) Control High Pulse wide(/RD) Control High Pulse wide(/WR) Data steup time Data hold time /RD access time(*a) Output disable time(*a) Note: *a. all timing is using 20﹪ ...
Page 8
... Team Source Display 3.4 Reset Timing Items Items Items Reset time Reset time Reset time Reset Low pules width Reset Low pules width Reset Low pules width Note: *a. all timing is using 20﹪ and 80﹪ of VDD as the reference. 4. Function specifications 4.1 The Parallel Interface ...
Page 9
... Team Source Display 4.2 Basic Setting To drive the LCD module correctly and provide normally display, please use the following seting 1> ADC = 0 (normal) 2> SHL select = 1(reverse) 3> LCD Bias Select = 1/7 4> Initial Display Line = 0 5> Entire Display ON/OF = OFF(normal) 6> Reverse Display ON/OF = OFF(normal) 7> Set Power Control Set: Voltage follower = ON,voltage converter = ON,Voltage regulator = ON 8> ...
Page 10
... Team Source Display 4.4 Display Commands Instrctions No. Display ON/OFF 1 Display start line set 2 Set Page Address 3 Ser Column Address (Upper-4 bits) 4 Ser Column Address (Lower-4 bits) Read Staus 5 Write Display Data 6 Read Display Data 7 ADC Select 8 Normal/Reverse Display 9 Entire Display ON/OFF 10 Set LCD Bias ...
Page 11
... Team Source Display 4.5 Basic Operating Sequence 4.5.1 Initialization Sequence Turn on Power Supply VDD & VSS While maintaining /RES at LOW Wait until power supply is stabilized Release the /RES Reset Signal (/RES = High) LCD Bias = 1/7 ADC = Normal SHL = Reverse Initial Display Line = 0 Power Control ...
Page 12
... Team Source Display 5. Inspection Standards Item (1) Non display 1) Display on inspection (3) Horizontal line is deficient (4) Cross line is deficient 2) Black／White spot Length (mm) 3) Black／White line Defects separate with each other at an interval of more than 20mm 4) Display pattern A+B≤0.28 0<C D+E≤0.25 Note damages acceptable ...
Page 13
... Team Source Display 6. Handling Precautions 6.1 Mounting method A panel of LCD module made by our company consists of two thin glass plates with polarizers that easily get damaged. And since the module in so constructed fixed by utilizing fitting holes in the printed circuit board (PCB), extreme care should be used when handling the LCD modules ...
Page 14
... Team Source Display www.tslcd.com LCM Specification ...