TMPM382FWFG Toshiba, TMPM382FWFG Datasheet - Page 601
TMPM382FWFG
Manufacturer Part Number
TMPM382FWFG
Description
Manufacturer
Toshiba
Datasheet
1.TMPM380FWDFG.pdf
(700 pages)
Specifications of TMPM382FWFG
Product Summaries
Summary
Lead Free
Yes
Rohs Compatible Product(s)
Available
Rom (kbytes)
128K
Rom Type
Flash
Ram (kbytes)
12K
Number Of Pins
64
Package
QFP(14x14)
Vcc
5V
Cpu Mhz
40
Ssp (ch) Spi
1
I2c/sio (ch)
1
Uart/sio (ch)
3
Usb
-
Can
-
Ethernet
-
External Bus Interface
N
Cs/wait Controller (ch)
-
Dma Controller
2
10-bit Da Converter
-
10-bit Ad Converter
-
12-bit Ad Converter
10
16-bit Timer / Counter
6
Motor / Igbt Control
Y
Real Time Clock
1
Watchdog Timer
Y
Osc Freq Detect
Y
Clock Gear
Y
Low-power Hold Function
-
Remote Control Interface
Y
Hardware Cec Controller
-
Comparators
-
Low-voltage Detector
Y
Etm Hardware Trace
2-bit
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 601 of 700
- Download datasheet (5Mb)
23 Flash Memory Operation
(3) Reset
(Note 1) Command sequences are executed from outside the flash memory area.
(Note 2) Each bus write cycle must be sequentially executed by 32-bit data transmit
(Note 3) For the command sequencer to recognize a command, the device must be in the
(Note 4) Upon issuing a command, if any address or data is incorrectly written, be sure to
predefined command write sequence, the flash memory will terminate the command execution
and return to the read mode.
command. While a command sequence is being executed, access to the flash
memory is prohibited. Also, don't generate any interrupt (except debug exceptions
when a DSU probe is connected).If such an operation is made, it can result in an
unexpected read access to the flash memory and the command sequencer may not
be able to correctly recognize the command. While it could cause an abnormal
termination of the command sequence, it is also possible that the written command
is incorrectly recognized.
read mode prior to executing the command. Be sure to check before the first bus
write cycle that the FLCS RDY/BSY bit is set to "1." It is recommended to
subsequently execute a Read command.
perform a software reset to return to the read mode again.
A hardware reset is used to cancel the operational mode set by the command write
operation when forcibly termination during auto programming/ erasing or abnormal
termination during auto operations occurs. The flash memory has a reset input as the
memory block and it is connected to the CPU reset signal. Therefore, when the RESET
input pin of this device is set to V
watch dog timer, the flash memory will return to the read mode terminating any automatic
operation that may be in progress. It should also be noted that applying a hardware reset
during an automatic operation can result in incorrect rewriting of data. In such a case, be
sure to perform the rewriting again.
Refer to Section 23.2.1 "Reset Operation" for CPU reset operations. After a given reset
input, the CPU will read the reset vector data from the flash memory and starts operation
after the reset is removed.
Hardware reset
TMPM380/M382 - 40 / 54 -
IL
or when the CPU is reset due to any overflow of the
TMPM380/M382
Related parts for TMPM382FWFG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet: