IR3897MTRPBF International Rectifier, IR3897MTRPBF Datasheet - Page 27
IR3897MTRPBF
Manufacturer Part Number
IR3897MTRPBF
Description
4A Highly Integrated Single-Input Voltage, Synchronous Buck Regulator in a PQFN package.
Manufacturer
International Rectifier
Datasheet
1.IR3897MTR1PBF.pdf
(42 pages)
Specifications of IR3897MTRPBF
Part Status
Active and Preferred
Package
PQFN / 4 x 5
Circuit
Single Output
Iout (a)
4
Switch Freq (khz)
0 - 1500
Input Range (v)
1.0 - 16
Output Range (v)
0.5 - 12
Pbf
PbF Option Available
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IR3897MTRPBF
Manufacturer:
INFINEON
Quantity:
2 140
When the control FET turns on in the next cycle, the
capacitor node connected to SW rises to the bus voltage
V
the voltage V
unchanged and the voltage at the Boot pin becomes:
A bootstrap capacitor of value 0.1uF is suitable for most
applications.
Input Capacitor Selection
The ripple current generated during the on time of the
control FET should be provided by the input capacitor.
The RMS value of this ripple is expressed by:
Where:
in
. However, if the value of C1 is appropriately chosen,
D is the Duty Cycle
I
Io is the output current.
For I
I
D
RMS
Figure 24: Bootstrap circuit to generate Vc voltage
RMS
is the RMS value of the input capacitor current.
o
=4A and D = 0.1, the I
V
V
V
in
o
Boot
I
27
c
o
across C1 remains approximately
V
D
FEBRUARY 02, 2012 |DATA SHEET | Rev 3.2
in
(1
V
cc
D
V
)
RMS
D
= 1.8A.
Single‐Input Voltage, Synchronous Buck Regulator
(13)
(14)
(12)
- 27 -
4A Highly Integrated SupIRBuck
Ceramic capacitors are recommended due to their peak
current capabilities. They also feature low ESR and ESL at
higher frequency which enables better efficiency.
For this application, it is advisable to have 3x10uF, 25V
ceramic capacitors, C3216X5R1E106M from TDK.
In addition to these, although not mandatory,
a 1x330uF, 25V SMD capacitor EEV‐FK1E331P from Panasonic
may also be used as a bulk capacitor and is recommended if
the input power supply is not located close to the converter.
Inductor Selection
The inductor is selected based on output power, operating
frequency and efficiency requirements. A low inductor value
causes large ripple current, resulting in the smaller size, faster
response to a load transient but poor efficiency and high
output noise. Generally, the selection of the inductor value
can be reduced to the desired maximum ripple current in the
inductor (Δi). The optimum point is usually found between
20% and 50% ripple of the output current.
For the buck converter, the inductor value for the desired
operating ripple current can be determined using the
following relation:
Where:
If Δi ≈ 30%*I
1.5μH. Select L=1.5μH, PCMB065T‐1R5MS, from Cyntec which
provides a compact, low profile inductor suitable for this
application.
V
V
Δi = Inductor Ripple Current
F
Δ
D – Duty Cycle
s
in
0
t
= Switching Frequency
V
– ON time
= Output Voltage
= Maximum input voltage
in
L
V
o
o
, then the output inductor is calculated to be
V
in
L
V
o
t
i
;
V
in
t
V
o
i F
D
*
TM
s
F
1
s
IR3897
PD‐97663
(15)