TLE 7272G Infineon Technologies, TLE 7272G Datasheet
TLE 7272G
Specifications of TLE 7272G
Related parts for TLE 7272G
TLE 7272G Summary of contents
Page 1
Low Drop Voltage Regulator Features Output voltage 5 V ±2% • • Ultra low current consumption: typ. 25µA • 300 mA current capability • Inhibit input • Reset • Very low-drop voltage • Short-circuit-proof • Suitable for use in ...
Page 2
Reset The Reset pin informs e.g. the microcontroller in case the output voltage has fallen below the lower threshold V of typ. 4.65 V. The hysteresis is typically 100mV. Connecting the RT regulator to a battery voltage at first the ...
Page 3
GND I RO AEP02825_7272 Figure 2 Pin Configuration P-TO252-5 (D-PAK), P-TO263-5 (D Table 1 Pin Definitions and Functions Pin No. Symbol Function 1 I Input; block to ground directly at the IC with a ceramic capacitor Reset Output; ...
Page 4
Table 2 Absolute Maximum Ratings Parameter Input I Voltage Current Output Q Voltage Voltage Current Reset Output RO Voltage Voltage Current Inhibit Input INH Voltage Current Temperature Junction temperature Storage temperature 1) Exposure to these absolute maximum ratings for extended ...
Page 5
Table 3 Operating Range Parameter Input voltage Junction temperature Note: In the operating range, the functions given in the circuit description are fulfilled. Table 4 Thermal Resistance Parameter Junction case Junction ambient Junction ambient 1) Worst case, regarding peak temperature; ...
Page 6
Application Information Table 5 Electrical Characteristics Parameter Output Q Output voltage Output voltage Output current limitation Output current limitation Current consumption – Current consumption – Quiescent ...
Page 7
Reset Output RO Reset switching threshold Reset Read Room Reset output low voltage Internal reset pull up resistor External reset pull up resistor Reset delay time Reset reaction time 1) An external reset pull up resistor is not required. Data ...
Page 8
itio ...
Page 9
Additionally a buffer capacitor C influences from load surges to the voltage levels. This one can either be an aluminum electrolytic capacitor or a tantalum capacitor following the application requirements. A general recommendation is to keep the drop over the ...
Page 10
Typical Performance Characteristics Current Consumption I q Junction Temperature µ µ ...
Page 11
Dropout Voltage V versus Output dr Current Dropout Voltage V versus Junction dr ...
Page 12
Region of Stability Ω ...
Page 13
Load Regulation dV versus Output Q Current Change ∆ Load Regulation ...
Page 14
Line Regulation dV versus Input Q Voltage ChangedV I 0 ∆ ...
Page 15
Line Transient Response Peak Voltage tim ...
Page 16
Reset Delay T Time versus Junction RD Temperature ...
Page 17
Package Outlines 0.15 max per side All metal surfaces tin plated, except area of cut. Figure 4 P-TO252-5-1 (Plastic Transistor Single Outline) Data Sheet +0.15 6.5 -0.10 5.4 ±0.1 A 5x0.6 ±0.1 1.14 4.56 0. TLE ...
Page 18
MAX. 0.15 MAX. per side 1) Includes mold flashes on each side. All metal surfaces tin plated, except area of cut. Figure 5 P-TO252-5-11 (Plastic Transistor Single Outline) Figure 6 Foot Print for P-TO-252-5-1 and P-TO-252-5-11 (Plastic Transistor Single ...
Page 19
Typical Metal surface min 7.25 6.9 All metal surfaces tin plated, except area of cut. Figure 7 P-TO263-5-1 (Plastic Transistor Single Outline) Figure 8 Foot Print for P-TO263-5-1(Plastic Transistor Single Outline) ...
Page 20
Remarks Data Sheet 20 TLE 7272 Rev. 1.1, 2005-07-30 ...
Page 21
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...