BTS 3205G Infineon Technologies, BTS 3205G Datasheet
BTS 3205G
Specifications of BTS 3205G
Related parts for BTS 3205G
BTS 3205G Summary of contents
Page 1
...
Page 2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
Smart Low-Side Power Switch HITFET 1 Overview Features • Low input current • Short circuit and Overload protection • Current limitation • Input protection (ESD) • Thermal protection with auto restart • Compatible to standard Power MOSFET • Analog driving ...
Page 4
Protective Functions • Electrostatic discharge protection (ESD) • Active clamp over voltage protection • Thermal shutdown with auto restart • Short circuit protection Fault Information • Thermal shutdown • Short to Battery and overload Applications • Designed for driving Relays ...
Page 5
Block Diagram Gate IN Driving Unit ESD Protection Figure 1 Block Diagram 2.1 Terms Figure 2 shows all external terms used in this data sheet GND Figure 2 Terms Data Sheet Over- Over- voltage ...
Page 6
Pin Configuration 3.1 Pin Assignment BTS3205G Source Figure 3 Pin Configuration PG-DSO-8-24 3.2 Pin Definitions and Functions Pin Symbol 1 Source Drain Data Sheet Pin ConfigurationPin Assignment BTS3205G 1 IN ...
Page 7
General Product Characteristics 4.1 Absolute Maximum Ratings 1) Absolute Maximum Ratings = -40 ⋅C to +150 ⋅C; all voltages with respect to ground, positive current flowing into pin T j (unless otherwise specified) Pos. Parameter Voltages 4.1.1 Drain voltage ...
Page 8
Thermal Resistance Pos. Parameter 4.2.1 Junction to Soldering Point 4.2.2 Junction to Ambient 1) Not subject to production test, specified by design. 2) Device mounted on PCB according EIA/JEDEC standard JESD51-7 (4-layer FR4, 76.2 mm × 114.3 mm with ...
Page 9
Figure 5 Typical Transient Thermal Impedance ...
Page 10
Block Description and Characteristics 5.1 Input and Power Stage 5.1.1 Input Circuit Figure 6 shows the input circuit of the BTS3205G. The zener Diode protects the input circuit against ESD pulses. The internal circuitry is supplied by the input ...
Page 11
Failure Feedback During failure condition the BTS3205G tries to sink a increased input current 5.1.3 Output On-State Resistance The on-state resistance depends on the junction temperature R on-state resistance . DS(on) Figure 9 Typical On-State Resistance, Data Sheet Block ...
Page 12
Power Dissipation The maximum allowed power dissipation in 1,00 0,10 0,01 Figure 10 Maximal Allowable Power Dissipation 5.1.5 Output Timing A voltage signal at the input pin above the threshold voltage causes the power MOSFET to switch on with ...
Page 13
Characteristics Note: Characteristics show the deviation of parameter at given input voltage and junction temperature. Typical values show the typical parameters expected from manufacturing. All voltages with respect to Source Pin unless otherwise stated. Electrical Characteristics: Input and Power ...
Page 14
Electrical Characteristics: Input and Power Stage (cont’d) = -40 ⋅C to +150 ⋅C , all voltages with respect to ground, positive current flowing into pin T j (unless otherwise specified Pos. Parameter Ω Switching = 12 ...
Page 15
Protection Functions The device provides embedded protection functions. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operation. 6.1 Thermal Protection The device is ...
Page 16
lamp V bb Figure 14 Switching an Inductance While demagnetization of inductive loads, energy has to be dissipated in the BTS3205G. This energy can be calculated with following equation ...
Page 17
Short Circuit Protection The condition short circuit is an overload condition of the device. If the current reaches the value of starts to limit the current. In the condition of current limitation the device heats up. If the thermal ...
Page 18
Characteristics Note: Characteristics show the deviation of parameter at given input voltage and junction temperature. Typical values show the typical parameters expected from manufacturing. Electrical Characteristics: Protection Functions T = -40 ⋅C to +150 ⋅C; all voltages with respect ...
Page 19
Package Outlines BTS3205G 1.27 +0.1 2) 0.41 -0.06 0 -0.2 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in ...
Page 20
Revision History Version Date Changes Rev. 1.1 2011-09-01 fixed a typo in EAR test conditions in chapter Max ratings updated Feature list and rephrased Detailed Description fixed a spelling error in 5.1.3 regarding “dependency” Rev. 1.0 2008-09-25 released data ...
Page 21
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...