AD843S Analog Devices, AD843S Datasheet
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD843S
Available stocks
Related parts for AD843S
AD843S Summary of contents
Page 1
... AD843J and AD843K are rated over the commercial temperature range +70 C. The AD843A and AD843B are rated over the industrial temperature range of – +85 C. The AD843S is rated over the military temperature range of – +125 C and is available processed to MIL-STD-883B, Rev. C. REV. D Information furnished by Analog Devices is believed to be accurate and reliable ...
Page 2
... AD843K AD843B AD843S AD843KN AD843BQ AD843SQ, AD843SQ/883B AD843BH AD843SH, AD843SH/883B AD843SE/883B AD843SCHIPS Units nV rms V/mV V/ MHz MHz ...
Page 3
... Storage Temperature Range ( – +125 C Storage Temperature Range ( – +150 C Operating Temperature Range AD843J +70 C AD843A – +85 C AD843S . . . . . . . . . . . . . . . . . . . . . . . . . . – +125 C Lead Temperature Range (Soldering 60 sec +300 C ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 V NOTES 1 Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device at these or any other conditions above those indicated in the operational sections of this specification is not implied ...
Page 4
AD843–Typical Characteristics Figure 1. Input Voltage Range vs. Supply Voltage Figure 4. Quiescent Current vs. Supply Voltage Figure 7. Input Bias Current vs. Common Mode Voltage Figure 2. Output Voltage Swing vs. Supply Voltage Figure 5. Input Bias Current vs. ...
Page 5
Figure 10. Open Loop Gain and Phase Margin vs. Frequency Figure 13. Common Mode Rejection vs. Frequency Figure 16. Harmonic Distortion vs. Frequency REV. D Figure 11. Open Loop Gain vs. Supply Voltage Figure 14. Large Signal Frequency Response Figure ...
Page 6
AD843–Typical Characteristics Figure 19. Open Loop Gain vs. Resistive Load Figure 20c. Inverter Small Signal Pulse Response Figure 21a. Unity Gain Inverter Circuit for Driving Capacitive Loads Figure 20a. Inverting Amplifier ...
Page 7
Figure 22a. Unity Gain Buffer Amplifier Figure 23a. Unity Gain Buffer Circuit for Driving Capacitive Loads Figure 23d. Buffer Cap Load Large Signal Pulse Response pF REV. D Figure 22b. Buffer Large Signal Pulse Response. ...
Page 8
AD843 GROUNDING AND BYPASSING Like most high bandwidth amplifiers, the AD843 is sensitive to capacitive loading. Although it will drive capacitive loads without degradation of its rated performance, both an increased capacitive load drive capability and ...
Page 9
SAMPLE-AND-HOLD AMPLIFIER CIRCUITS A Fast Switching Sample & Hold Circuit A sample-and-hold circuit possessing short acquisition time and low aperture delay can be built using an AD843 and discrete JFET switches. The circuit of Figure 25 employs five n-channel JFETs ...
Page 10
AD843 equal. Alternatively, an autocalibration circuit using two D/A converters can be employed. This can also be used to calibrate out the effects of offset voltage drift over temperature. The switch choice, for U1s, is critical in this type of ...
Page 11
MEASURING AD843 SETTLING TIME Figure 28 shows the dynamic response of the AD843 while op- erating in the settling time test circuit of Figure 27. The input of the settling time fixture is driven by a flat-top pulse generator. The ...
Page 12
AD843 Mini-DIP Package (N-8) TO-8 Package (H-12A) OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 0.4133 (10.50) 0.3977 (10.00 PIN 1 0.0118 (0.30) 0.0040 (0.10) 0.0500 (1.27) BSC LCC Package (E-20A) 0.082 0.018 0.350 0.008 SQ (2.085 0.455) ...