MB15E03 Fujitsu, MB15E03 Datasheet
![no-image](/images/manufacturer_photos/0/2/267/fujitsu_sml.jpg)
MB15E03
Available stocks
Related parts for MB15E03
MB15E03 Summary of contents
Page 1
... MB15E03 DESCRIPTION The Fujitsu MB15E03 is serial input Phase Locked Loop (PLL) frequency synthesizer with a 1.2 GHz prescaler. A 64/ 128/129 can be selected for the prescaler that enables pulse swallow operation. The latest BiCMOS process technology is used, resuItantly a supply current is limited as low as 3.5 mA typ. This operates with a supply voltage of 3 ...
Page 2
... MB15E03 PIN ASSIGNMENTS SSOP-16 pin BCC-16 pin 2 OSCin OSCout LD/fout Vcc TOP VIEW GND Xfi Data fin Clock 8 9 (FPT-16P-M05) OSCin OSCout LD/fout TOP VIEW ...
Page 3
... The output signal is selected by LDS bit in the serial data. LDS = ”H” ; outputs fout (fr/fp monitoring output) LDS = ”L” ; outputs LD (”H” at locking, ”L” at unlocking.) Phase comparator output for an external charge pump. Nch open O drain output. Phase comparator output for an external charge pump. CMOS O output. MB15E03 3 ...
Page 4
... MB15E03 BLOCK DIAGRAM OSC 1 IN Crystal Oscillator circuit OSC 2 OUT Intermittent mode control PS 12 (power save) 1-bit control LE 11 latch Data 10 Clock Prescaler 64/65, 128/129 GND Note: SSOP-16 pin 4 Programmable reference divider Binary 14-bit reference counter fr SW ...
Page 5
... FUJITSU representative beforehand. Symbol Rating V –0 –0 +0 –0 +0 –55 to +125 stg Value Symbol Min. Typ. V 2.7 3 – GND – –40 – MB15E03 Unit Remark Unit Remark Max. 3 ...
Page 6
... MB15E03 ELECTRICAL CHARACTERISTICS Parameter Power supply current* 1 Power saving current Operating frequency Crystal oscillator operating frequency fin Input sensitivity OSCin Data, Clock, Input voltage LE, PS, ZC Data, Clock, LE, PS Input current ZC OSCin P R, LD/fout Output voltage Do High impedance Do cutoff current P R, LD/fout ...
Page 7
... LDS : LD/fout signal select bit Note: Start data input with MSB first A Destination of serial data Data MB15E03 127 LDS [Table. 1] [Table. 2] [Table. 5] [Table. 7] [Table ...
Page 8
... MB15E03 Programmable Reference Counter CNT: Control bit N1 to N11: Divide ratio setting bits for the programmable counter (5 to 2,047 A7: Divide ratio setting bits for the swallow counter (0 to 127) Note: Start data input with MSB first Table2 ...
Page 9
... < High impedance 64/65 P LD/fout Do L (fr (fr (fr) Z* MB15E03 ) OUT , R, and P is shown below Low R P LD/fout H Z* (fp (fp (fp) 9 ...
Page 10
... MB15E03 When designing a synthesizer, the FC pin setting depends on the VCO and LPF characteristics. : When the LPF and VCO characteristics are similar to (1), set FC bit high. : When the VCO characteristics are similar to (2), set FC bit low. PLL LPF Power Saving Mode (Intermittent Mode Control Circuit) Setting a PS pin to Low, the IC enters into power saving mode resultatly current sonsumption can be limited (max ...
Page 11
... Clock Data LE PS Table.9 ZC Pin Setting ZC pin Do output H Normal output L High impedance ( (power saving mode) at Power-ON. (2) Set serial data after power supply remains stable. (3) Release saving mode (PS: LfiH) after setting serial data. MB15E03 ...
Page 12
... MB15E03 SERIAL DATA INPUT TIMING Data MSB Clock rising edge of the clock, one bit of the data is transferred into the shift register. Parameter Min Typ. Max. Unit Parameter ns t5 – – ns – – – ...
Page 13
... OSCin input frequency > 8/fosc ( < 16/fosc ( becomes high during the power saving mode (PS = ”L”.) more. LD output becomes high when phase error > 625ns, foscin = 12.8 MHz) < 1250ns, foscin = 12.8 MHz) MB15E03 WL 13 ...
Page 14
... MB15E03 TEST CIRCUIT (FOR MEASURING INPUT SENSITIVITY FIN/OSCIN) 1000pF P • G 1000pF 50 Controller (setting divide ratio) Note: SSOP-16 pin 0.1 F 1000pF 0 Vcc P • G Oscilloscope ...
Page 15
... OSC V IN OUT P X’ tal 0 Depend on the crystal parameters 1 2 Note: SSOP-16 pin LPF Data Clock MB15E03 GND 1000pF 0.1 F MB15E03 Output VCO To a lock detect. From a controller f IN 1000pF 15 ...
Page 16
... MB15E03 TYPICAL CHARACTERISTICS Do Output Current [ 5.0 4.0 3.0 2.0 1.0 0 –5 0 –10 I (mA) OH fin Input Sensitivity [Ta = +25 C] +10 0 –10 –20 –30 –40 0 OSCin Input Characteristics [Ta = +25 C] +10 SPEC 0 –10 –20 –30 – 5 4.0 3.0 2.0 1.0 0 –15 –20 0 SPEC 500 1000 fi ...
Page 17
... MHz STOP 1 200.000 000 MHZ 2: 694.75 –5.339 k 2.981 pF 10.000 000 MHz STOP 40.000 000 MHZ MB15E03 1: 232.63 –556.66 100 MHz 2: 22.031 –150.96 400 MHz 3: 9.8965 –59.148 800 MHz 1: 4.094 k –15.619 k 3 MHz 3: 437 ...
Page 18
... MB15E03 REFERENCE INFORMATION Typical plots measured with the test circuit are shown below. Each plot shows lock up time, phase noise and reference leakage. PLL Lock Up Time = 440 s (1005.000 MHz 1031.000 MHz, within MKr x : 439.89783 25.94979 MHz 30.00300 MHz 1.000 kHz/div 29 ...
Page 19
... ORDERING INFORMATION Part number MB15E03 PFV1 MB15E03 PV Package 16 pin, Plastic SSOP (FPT-16P-M05) 16 pin, Plastic BCC (LCC-16P-M02) MB15E03 Remarks 19 ...
Page 20
... MB15E03 PACKAGE DIMENSIONS 16 pins, Plastic SSOP (FPT-16P-M05) * 5.00±0.10(.197±.004) INDEX 0.65±0.12 (.0256±.0047) 4.55(.179)REF 1994 FUJITSU LIMITED F16013S-2C These dimensions do not include resin protrusion. * 4.40±0.10 6.40±0.20 (.173±.004) (.252±.008) "A" +0.10 0.22 –0.05 +.004 .009 – ...
Page 21
... OFF) Details of "A" part 0.75±0.10 (.030±.004) 0.40±0.10 (.016±.004) MB15E03 3.40(.134)TYP 0.65(.026)TYP 14 0.40±0.10 (.016±.004) "A" 1.15(.045)TYP "B" 1.725(.068) 1 TYP Details of "B" part 0.60± ...
Page 22
... MB15E03 FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-88, Japan Tel: (044) 754-3763 Fax: (044) 754-3329 North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, U ...