CMMDW24S5-4000 Wall Industries,Inc., CMMDW24S5-4000 Datasheet - Page 2

• Manufacturer Part Number: CMMDW24S5-4000
• Description: 20w Dc/dc Chassis Mount Converter 9-36 Vdc Input 5 Vdc Single Output At 4000ma
• Manufacturer: Wall Industries,Inc.

(888) 597-WALL
Technical Specifications
SPECIFICATION
INPUT (V
Operating Voltage Range
UVLO Turn-on Threshold
UVLO Turn-off Threshold
Input Standby Current
Input Current
Input Voltage
Input Voltage Variation
Reflected Ripple Current
Start Up Time
(Nominal Vin and constant resistive load)
OUTPUT (V
Output Voltage Range
Load Regulation
Line Regulation
Voltage Adjustability
Output Ripple & Noise (20MHz)
Output Current
Output Voltage Overshoot
PROTECTION
Over Voltage Protection
Over Current Protection
Short Circuit Protection
DYNAMIC LOAD RESPONSE
Peak Deviation
Setting Time (Vout < 10% peak deviation)
REMOTE ON/OFF
Negative Logic (Option)
Positive Logic (Standard)
Remote OFF Input Current
Input Current of Remote Control Pin
GENERAL
Switching Frequency
Efficiency
ISOLATION
Isolation Voltage (Input-Output)
Isolation Voltage (Output to Case)
Isolation Voltage (Input to Case)
Isolation Resistance
Isolation Capacitance
ENVIRONMENTAL
Operating Ambient Temperature (with derating)
Operating Case Temperature
Storage Temperature
Temperature Coefficient
MTBF
Bellcore TR-NWT-000332, T
MIL-HDBK-217F
MECHANICAL
Weight
Dimensions
in
)
o
)
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
(see page 6)
C
=40°C
We reserve the right to change specifications based on technological advances.
Related condition
Nominal Vin and No Load
Nominal Vin and Full Load
Continuous
Transient (100ms)
Complies with ETS300 132 part 4.4
5 to 20MHz, 12µH source impedance
(See the Test Setup section - pg 9)
Power Up
Remote On/Off
Nominal Vin and Full Load; Ta = 25°C
0% to 100% Full Load
LL to HL at Full Load
Measured with a 0.1µF/50V MLCC
(See the Test Setup section - pg 9)
LL to HL at Full Load and 25°C
Zener diode clamp
Test at nominal Vin and 25°C
Load step change from 75 to 100% or 100 to 75 % of FL
Load step change from 75 to 100% or 100 to 75 % of FL
The ON/OFF pin voltage is referenced to -Vin
(See the Remote ON/OFF Control section - pg 7)
DC/DC ON
DC/DC OFF
DC/DC ON
DC/DC OFF
Nominal Vin, and full load; Ta=25°C
(See the Test Setup section – pg 9)
See the MTBF and Reliability section (pg 10)
www.wallindustries.com
Rev. A
TECHNICAL DATASHEET
M
M
CMMDW24S5-4000
o
o
d
d
e
e
l
l
N
N
-0.02
Min
1600
1600
1600
4.95
-0.5
-0.2
-0.5
-10
-40
-55
o
4.00(L) x 2.25(W) x 0.81(H) inches
o
9
0
0
3
3
0
1
101.6(L) x 57.2(W) x 20.6(H) mm
.
.
Hiccup, automatic-recovery
1,621,000
659,000
Nom
CMMDW24S5-4000
150
200
250
400
7.5
6.2
2.5
24
65
20
75
88
See Figure 1
9
5
0
6 oz
Page 2 of 11
+0.02
Max
4000
1500
5.05
+0.5
+0.2
992
+10
105
105
125
1.2
1.2
0.5
36
36
50
20
20
12
12
5
5
mA
mV
% Vout
% / °C
% FL
V/ms
hours
hours
Unit
KHz
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
mA
mA
mA
mV
mA
mA
GΩ
ms
pF
°C
°C
°C
%
%
µs
%
%
pk-pk
pk-pk