Z4K121-RI-10 Superworld Electronics, Z4K121-RI-10 Datasheet
![no-image](/images/no-image-200.jpg)
Z4K121-RI-10
Related parts for Z4K121-RI-10
Z4K121-RI-10 Summary of contents
Page 1
... Storage temp. : -55°C to +125°C d) Operating temp. : -55°C to +125°C e) Resistance to solder heat : 260°C.10secs NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD (a) Series code (b) Dimension code (c) Material code (d) Impedance code : 221 = 220 ...
Page 2
... FERRITE CHIP BEADS 6. ELECTRICAL CHARACTERISTICS : EIA Part Number Size Z4K121-RI-10 1206 Z4K151-RI-10 1206 Z4K221-RG-10 1206 Z4K301-RG-10 1206 Z4K471-RD-10 1206 Z4K601-RD-10 1206 Z4K801-RC-10 1206 Z4K102-RC-10 1206 Z4V152-RC-10 1206 Z4V202-RC-10 1206 7. IMPEDANCE VS. FREQUENCY CURVES : Z4K1 21 -RI-1 0 Z4K121-R I- 3216K-1 21T 09 400 300 200 ...
Page 3
... Z4V1 52-RC 4V152-RC - 3216 V-152T03 2500 2000 1500 1000 500 EQU EN CY(MH z) NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD 1000 800 600 Z 400 200 R X 100 1000 1500 Z 1000 ...
Page 4
... Flexture Strength The terminal electrode & the dielectric must not be damaged by the forces applied on the right conditions. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD PERFORMANCE Preheating Dipping Natural cooling 260° ...
Page 5
... For the detail derating of current, please refer to the Derated Current vs. Operating Temperature curve. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD PERFORMANCE 1.0(0.039) R0.5(0.02) ...
Page 6
... Time(sec.) Figure 1. Re-flow Soldering NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD PC board should be designed so that products are not sufficient under mechanical stress as warping the board. Products shall be positioned in the sideway direction against the mechanical stress to prevent failure ...
Page 7
... Accordingly increasing the solder volume, the mechanical stress to product is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. Solder shall be used not to be exceed as shown in Fig. 4. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD Z4 SERIES Upper limit ...
Page 8
... Material : Plastic D:1.5+0.1 Po:4±0.1 P2:2±0. D1:1±0.1 10-2.1 Tape Dimension / 12mm Po:4±0.1 P2:2±0.05 D:1.5+0 D1:1.5±0.1 NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD 2±0.5 7" x 12mm R1.9 t Series Size 3(09 Series Size 3(09 3(12 ...
Page 9
... Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) The use of tweezers or vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD ...