ST92141 STMicroelectronics, ST92141 Datasheet - Page 154
ST92141
Manufacturer Part Number
ST92141
Description
8/16-bit Mcu For 3-phase Ac Motor Control
Manufacturer
STMicroelectronics
Datasheet
1.ST92141.pdf
(179 pages)
- Current page: 154 of 179
- Download datasheet (3Mb)
ST92141 - ANALOG TO DIGITAL CONVERTER (ADC)
REGISTER DESCRIPTION (Cont’d)
CONTROL LOGIC REGISTER (CLR)
The Control Logic Register (CLR) manages the
ADC’s logic. Writing to this register will cause the
current conversion to be aborted and the autoscan
logic to be re-initialized. CLR is programmable as
follows:
CONTROL LOGIC REGISTER (CLR)
R253 - Read/Write
Register Page: 63
Reset Value: 0000 0000 (00h)
Bit 7:5 = SC[2:0]: Start Conversion Address .
These 3 bits define the starting analog input chan-
nel (Autoscan mode). The first channel addressed
by SC[2:0] is converted, then the channel number
is incremented for the successive conversion, until
channel 7 (111) is converted. When SC2, SC1 and
SC0 are all set, only channel 7 will be converted.
Bit 4 = EXTG: External Trigger Enable .
This bit is set and cleared by software.
0: External trigger disabled.
1: External trigger enabled. Allows a conversion
Bit 3 = INTG: Internal Trigger Enable .
This bit is set and cleared by software.
0: Internal trigger disabled.
1: Internal trigger enabled. Allows a conversion se-
154/179
SC2
sequence to be started on the subsequent edge
of the external signal applied to the EXTRG pin
(when enabled as an Alternate Function).
quence to be started, synchronized by an inter-
nal signal (On-chip Event signal) from a Multi-
function Timer peripheral.
7
9
SC1
SC0
EXTG
INTG
POW CONT
ST
0
Both External and Internal Trigger inputs are inter-
nally ORed, thus avoiding Hardware conflicts;
however, the correct procedure is to enable only
one alternate synchronization input at a time.
Note: The effect of either synchronization mode is
to set the START/STOP bit, which is reset by hard-
ware when in SINGLE mode, at the end of each
sequence of conversions.
Requirements: The External Synchronisation In-
put must receive a low level pulse wider than an
INTCLK period and, for both External and On-Chip
Event synchronisation, the repetition period must
be greater than the time required for the selected
sequence of conversions.
Bit 2 = POW: Power Up/Power Down.
This bit is set and cleared by software.
0: Power down mode: all power-consuming logic is
1: Power up mode: the A/D converter logic and an-
Bit 1 = CONT: Continuous/Single .
0: Single Mode: a single sequence of conversions
1: Continuous Mode: the first sequence of conver-
Bit 0 = ST: Start/Stop.
0: Stop conversion. When the A/D converter is
1: Start a sequence of conversions.
disabled, thus selecting a low power idle mode.
alog circuitry is enabled.
is initiated whenever an external (or internal)
trigger occurs, or when the ST bit is set by soft-
ware.
sions is started, either by software (by setting
the ST bit), or by hardware (on an internal or ex-
ternal trigger, depending on the setting of the
INTG and EXTG bits); a continuous conversion
sequence is then initiated.
running in Single Mode, this bit is hardware re-
set at the end of a sequence of conversions.
Related parts for ST92141
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
(ST62T15C / ST62T25C) 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
(ST62E35B / ST62T35B) 8-BIT OTP/EPROM MCUs
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
8-BIT OTP/EPROM MCU WITH LCD DRIVER / EEPROM AND A/D CONVERTER
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
AUdio Amplifier
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
NPN MEDIUM POWER TRANSISTOR
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
(ST90135 / ST90158) Microcontroller
Manufacturer:
ST Microelectronics
Part Number:
Description:
(ST90x27 / ST90x28) 16K EPROM HCMOS MCUS WITH RAM
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
(ST90R28B6) 16K ROM / 256 RAM HCMOS MCUs
Manufacturer:
ST Microelectronics
Part Number:
Description:
(ST90x31) 8K EPROM HCMOS MCU
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
(ST92195C/D) 48-96 Kbyte ROM HCMOS MCU
Manufacturer:
ST Microelectronics
Part Number:
Description:
16-48K ROM HCMOS MCU WITH ON SCREEN DISPLAY AND VOLTAGE TUNINGOUTPUT
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
48K ROM HCMOS MCUs WITH ON SCREEN DISPLAY AND A/D CONVERTER
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
24K ROM HCMOS MCU WITH ON SCREEN DISPLAY AND CLOSED-CAPTION DATA SLICER
Manufacturer:
ST Microelectronics
Datasheet: