7MBP100RTJ060 Fuji Electric holdings CO.,Ltd, 7MBP100RTJ060 Datasheet
![no-image](/images/manufacturer_photos/0/2/265/fuji_electric_holdings_co__ltd_sml.jpg)
7MBP100RTJ060
Available stocks
Related parts for 7MBP100RTJ060
7MBP100RTJ060 Summary of contents
Page 1
...
Page 2
...
Page 3
Outline Drawings ±0 ±0 6-M5 φ2.5 (φ1∼1.5) Fuji Electric Co.,Ltd ± ±0 ...
Page 4
Descriptions Main circuit Symbol Control circuit № Symbol ① GNDU ② ALMU ③ VinU ④ VccU ⑤ GNDV ⑥ ALMV ⑦ VinV ⑧ VccV ⑨ GNDW ⑩ ALMW ⑪ VinW ⑫ VccW ...
Page 5
Diagram VccU VccU ④ ④ VinU VinU ③ ③ ALMU ALMU ② ② 1.5k 1.5k ALM ALM GNDU GNDU ① ① VccV VccV ⑧ ⑧ VinV VinV ⑦ ⑦ ALMV ALMV ⑥ ⑥ 1.5k ...
Page 6
Maximum Ratings Tc=25℃ unless otherwise specified. Items Bus Voltage (between terminal P and N) Collector-Emitter Voltage *1 Collector Current Collector Power Dissipation Collector Current Forward Current of Diode Collector Power Dissipation Supply Voltage of Pre-Driver *4 Input Signal ...
Page 7
Characteristics Tj=25℃,Vcc=15V unless otherwise specified. 5.1 Main circuit Item Symbol Collector Current at off signal input Collector-Emitter VCE ( s a t ) saturation voltage Forward voltage of FWD Collector Current at off signal input Collector-Emitter VCE ( ...
Page 8
Protection Section (Vcc=1 5 V ) Item Over Current Protection Level of Inverter circuit Over Current Protection Level of Brake circuit Over Current Protection Delay time SC Protection Delay time IGBT Chips Over Heating Protection Temperature Level Over Heating ...
Page 9
Figure 1. Switching Time Waveform Definitions /Vin Gate On Vge (Inside IPM) Fault (Inside IPM) normal /ALM Figure 2. Input/Output Timing Diagram Necessary conditions for alarm reset (refer ...
Page 10
ALM ALM Figure.4 Definition of tsc VccU 20k DC VinU 15V SW1 GNDU Vcc 20k DC VinX 15V SW2 GND Earth Figure 5. Noise Test Circuit DC DC 15V 15V HCPL- HCPL- 4504 4504 Figure 6. ...
Page 11
Truth table 10.1 IGBT Control The following table shows the IGBT ON/OFF status with respect to the input signal Vin. The IGBT turn-on when Vin is at “Low ” level under no alarm condition. 10.2 Fault Detection ...
Page 12
Cautions for design and application 1. Trace routing layout should be designed with particular attention to least stray capacity between the primary and secondary sides of optical isolators by minimizing the wiring length between the optical isolators and ...
Page 13
Taking the used isolator’s CTR into account, design with a sufficient allowance to decide 10. the primary forward current of the optical isolator. フォ ト カプラの一次側電流は、お使いのフォ ト カプラの CTR を考慮し十分に余裕をもった設計にして下さい 。 11. Apply thermal compound to the surfaces between the ...
Page 14
... This specification is applied to the IGBT-IPM (type: 7MBP100RTJ060). 本仕様書は、IGBT-IPM (型式:7MBP100RTJ060)に適用する ...
Page 15
...
Page 16
...
Page 17
...
Page 18
...
Page 19
...
Page 20
Test Items Test cate- Test items gories 1 Terminal Strength Pull force 端子強度 (Pull test) Test time 2 Mounting Strength Screw torque 締め付け強度 Test time 3 Vibration Range of frequency : 10 ~ 500Hz 振動 Sweeping time Acceleration Sweeping ...
Page 21
Test Items Test cate- Test items gories 1 High temperature Reverse Bias Test tepm. 高温逆バイアス Bias Voltage Bias Method Test duration 2 Temperature Test tepm. hummidity baias Relative humidity 高温高湿バイアス Bias Voltage Bias Method Test duration 3 Intermitted ON ...
Page 22
This product shall be used within its abusolute maximun rating (voltage, current, and temperature). This product may be broken in case of using beyond the ratings. 製品の絶対最大定格 (電圧,電流,温度等 )の範囲内で御使用下さい 。絶対最大定格を超えて使用すると 、素 子が破壊する場合があります 。 2. Conect adequate fuse or protector ...
Page 23
According to the outline drawing, select proper length of screw for main terminal. Longer screws may break the case. 本 製 品に使用する主端子用のネジの長さは、外形図に従い正し く選定下さい。ネジが長いとケースが破 損する場合があります。 excessive static electricity is applied to the control terminals, the devices can be ...