LT1256 Linear Technology Corporation, LT1256 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
LT1256
Manufacturer Part Number
LT1256
Description
40mhz Video Fader And Dc Gain Controlled Amplifier
Manufacturer
Linear Technology Corporation
Datasheet
1.LT1256.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LT1256CN#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1256CS
Manufacturer:
LTNEAR
Quantity:
20 000
Company:
Part Number:
LT1256CS#PBF
Manufacturer:
LT
Quantity:
51
Part Number:
LT1256CS#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1256CS#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
LT1251/LT1256
APPLICATIONS
Control Circuit Description
The control section of the LT1251/LT1256 consists of two
identical voltage-to-current converters (V-to-I); each
V-to-I contains an op amp, an NPN transistor and a
resistor. The converter on the right generates a full-scale
current I
current I
minimum of zero (when I
(when I
gain from each signal input to the output.
The op amp in each V-to-I drives the transistor until the
voltage at the inverting input is the same as the voltage at
the noninverting input. If the open end of the resistor (Pin
5 or 10) is grounded, the voltage across the resistor is the
same as the voltage at the noninverting input. The emitter
current is therefore equal to the input voltage V
the resistor value R
the same as the emitter current and it is the ratio of the two
collector currents that sets the gain.
The LT1251/LT1256 are tested with Pins 5 and 10 grounded
and a full-scale voltage of 2.5V applied to V
sets I
applied to Pin 3. When the control voltage is negative or
zero, I
I
channel one goes from 0% to 100% as V
to 2.5V. The gain of channel two goes the opposite way,
from 100% down to 0%. The worst-case error in K (the
14
R
V
V
C
I
C
C
C
+
is equal to or greater than I
3
4
5
FS
C
C
at approximately 500 A; the control voltage V
is zero and K is zero. When V
CONTROL V TO I
FS
C
is equal to, or greater than, I
+
–
. The ratio I
Figure 3. Control Circuit Block Diagram
and the one on the left generates a control
C
R
5k
C
U
C
. The collector current is essentially
I
C
C
/I
INFORMATION
FS
C
U
is zero) to a maximum of one
is called K. K goes from a
FS
and K is one. The gain of
I
FS
W
FS
C
FULL SCALE V TO I
). K determines the
is 2.5V or greater,
C
R
FS
5k
FS
goes from zero
FS
(Pin 12). This
+
–
C
divided by
U
10
11
12
1251/56 F03
C
V
I
R
FS
FS
FS
is
gain) is 3% as detailed in the electrical tables. By using
a 2.5V full-scale voltage and the internal resistors, no
additional errors need be accounted for.
In the LT1256, K changes linearly with I
is zero, V
the worst-case control op amp offset. Similarly to insure
that K is 100%, V
the guaranteed gain accuracy.
To eliminate the overdrive requirement, the LT1251 has
internal circuitry that senses when the control current is at
about 5% and sets K to 0%. Similarly, at about 95% it sets
K to 100%. The LT1251 guarantees that a 2% (50mV)
input gives zero and 98% (2.45V) gives 100%.
The operating currents of the LT1251/LT1256 are derived
from I
of V
current for three values of V
mate formula for the supply current is:
where V
By reducing I
ever, the slew rate and bandwidth will also be reduced as
indicated in the characteristic curves. Using the internal
resistors (5k) with V
500 A; there is no reason to use a larger value of I
The inverting inputs of the V-to-I converters are available
so that external resistors can be used instead of the
internal ones. For example, if a 10V full-scale voltage is
desired, an external pair of 20k resistors should be used to
set I
greater than the maximum V
transistors from saturating. Do not use the internal resis-
tors with external resistors because the internal resistors
have a large positive temperature coefficient (0.2%/ C)
that will cause gain errors.
If the control voltage is applied to the free end of resistor
R
of the control voltage must be inverted. Therefore, K will
be 0% for zero input and 100% for – 2.5V input, assuming
V
ground; this is convenient for summing several negative
going control signals.
C
FS
I
(Pin 5) and the V
S
FS
equals 2.5V. With Pin 3 grounded, Pin 4 is a virtual
FS
= 1mA + (24)(I
FS
to 500 A. The positive supply voltage must be 2.5V
and R
S
and therefore the quiescent current is a function
C
is the total supply voltage between Pins 9 and 7.
must be negative 15mV or more to overcome
FS
FS
. The electrical tables show the supply
the supply current can be reduced, how-
C
C
must be 3% larger than V
FS
FS
input (Pin 3) is grounded, the polarity
) + (V
equal to 2.5V results in I
FS
S
/20k)
including zero. An approxi-
C
and/or V
C
. To insure that K
FS
to keep the
FS
FS
based on
equal to
FS
.