MTV003 ETC-unknow, MTV003 Datasheet
MTV003
Available stocks
Related parts for MTV003
MTV003 Summary of contents
Page 1
... On-chip clock oscillator allows external TTL level clock signal input. GENERAL DESCRIPTION MTV003 is intended for use in digital-controlled, power-conscious (Green) monitor applications. It integrates 4 major function blocks traditionally implemented in discrete parts and provides an easy interface for microprocessor controls. The functional blocks included in MTV003 are: SYNC processing, D/A converters, self-test pattern generator and command interface ...
Page 2
... X2. An appropriate capacitor to Ground, whose value depends on the specified the crystal, must be connected. This pin can also be used as a direct input when the external oscillator is used. Function MTV003 Revision 2.3 07/01/1998 2/13 MTV003N (MTV003) ...
Page 3
... There are 2 types of D/A converters with 8-bit resolution: open-drain type (DA0 to DA2) and CMOS type (XDA0 to XDA4). The sampling frequency is 31.25KHz or 15.625KHz, depending on the use of the crystal. The maximum external voltage applied is 12V for the open-drain type, and the output pulse width is programmable Function MTV003 Revision 2.3 07/01/1998 3/13 MTV003N (MTV003) ...
Page 4
... MTV003N (MTV003) Comment - - Tolerance (%) 0.0981354 0.1169591 0.1364256 0.1876172 0.1972386 0.2096436 0.2222222 0.2304147 0.2375297 0.2500000 0.3003003 0.3125000 0.3571428 0.3759398 0.4000000 0.6250000 MTV003 Revision 2.3 07/01/1998 ...
Page 5
... B13 B14 B15 HF10 HF9 HF8 HF2 HF1 HF0 x VCFF VF8 VF2 VF1 VF0 B13 B14 B15 cvs MTV003 Revision 2.3 07/01/1998 ...
Page 6
... DA0 b5 DA0 b6 DA0 b7 DA1 b5 DA1 b6 DA1 b7 DA2 b5 DA2 b6 DA2 XA0 b5 XA0 b6 XA0 b7 XA1 b5 XA1 b6 XA1 b7 XA2 b5 XA2 b6 XA2 b7 XA3 b5 XA3 b6 XA3 b7 XA4 b5 XA4 b5 XA4 -> negative -> not present -> low -> not valid. MTV003 Revision 2.3 07/01/1998 ...
Page 7
... Output pulse width control for DA2. Reg13 (write) : Reserved. -> force V pol = 1. -> force V pol = -> not valid. -> Normal mode. -> Test mode, not allowed in applications. -> CLK = X1 divided by 2 (for 8MHz crystal power-on [default]). -> CLK = X1 (for 4MHz crystal power-on [default]). 7/13 MTV003N (MTV003) MTV003 Revision 2.3 07/01/1998 ...
Page 8
... Enables generator. -> Disables generator. -> 63.5KHz (horizontal) output selected. -> 31.75 KHz (horizontal) output selected. -> Positive cross-hatch pattern output. -> Negative cross-hatch pattern output. -> Full white pattern output. -> Full black pattern output. -> Enables STOUT output. -> Disables STOUT output. 8/13 MTV003N (MTV003) MTV003 Revision 2.3 07/01/1998 ...
Page 9
... IDAOL = 3 mA (for pins of DA2-0) - (for pins of DA2-0, pulled up by external 5 to 12V power supply) Vin = VDD, Iout = 0 uA. (all input pins connected to VDD, all output pins without connection) 9/13 MTV003N (MTV003) Max. Unit VDD+ 2.4 V 0.3 0 MTV003 Revision 2.3 07/01/1998 ...
Page 10
... H-line - - - - (+/-) (+/-) 25 200 - 100 - 200 - 100 - 200 - 200 - 100 - MTV003 Revision 2.3 07/01/1998 10/13 MTV003N (MTV003) Unit - KHz - MHz 100 KHz 100 Hz 6 ...
Page 11
... MYSON TECHNOLOGY 8.0 TIMING DIAGRAMS MTV003 Revision 2.3 07/01/1998 11/13 MTV003N (MTV003) ...
Page 12
... MYSON TECHNOLOGY Figure 6. 4 Self-Test Patterns 12/13 MTV003N (MTV003) MTV003 Revision 2.3 07/01/1998 ...
Page 13
... MYSON TECHNOLOGY Figure 7. Self-Test Timing 13/13 MTV003N (MTV003) MTV003 Revision 2.3 07/01/1998 ...