M50FLW040B ST Microelectronics, M50FLW040B Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
M50FLW040B
Manufacturer Part Number
M50FLW040B
Description
4 Mbit 3V Supply Firmware Hub / Low Pin Count Flash Memory
Manufacturer
ST Microelectronics
Datasheet
1.M50FLW040B.pdf
(52 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M50FLW040BK5G
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Company:
Part Number:
M50FLW040BN5
Manufacturer:
ST
Quantity:
20
www.DataSheet4U.com
M50FLW040A, M50FLW040B
SIGNAL DESCRIPTIONS
There are two distinct bus interfaces available on
this device. The active interface is selected before
power-up, or during Reset, using the Interface
Configuration Pin, IC.
The signals for each interface are discussed in the
Firmware Hub/Low Pin Count (FWH/LPC) Signal
Descriptions
Multiplexed (A/A Mux) Signal Descriptions
tion, respectively, while the supply signals are dis-
cussed in the
Firmware Hub/Low Pin Count (FWH/LPC)
Signal Descriptions
Please see
Input/Output Communications (FWH0/LAD0-
FWH3/LAD3). All Input and Output Communica-
tions with the memory take place on these pins.
Addresses and Data for Bus Read and Bus Write
operations are encoded on these pins.
Input
LFRAME). The Input Communication Frame
(FWH4/LFRAME) signal indicates the start of a
bus operation. When Input Communication Frame
is Low, V
bus operation is initiated. If Input Communication
Frame is Low, V
operation is aborted. When Input Communication
Frame is High, V
ther proceeding or the bus is idle.
Identification Inputs (ID0-ID3). Up to 16 memo-
ries can be addressed on a bus, in the Firmware
Hub (FWH) mode. The Identification Inputs allow
each device to be given a unique 4-bit address. A
‘0’ is signified on a pin by driving it Low, V
leaving it floating (since there is an internal pull-
down resistor, with a value of R
on a pin by driving it High, V
leakage current of I
By convention, the boot memory must have ad-
dress ‘0000’, and all additional memories are giv-
en addresses, allocated sequentially, from ‘0001’.
In the Low Pin Count (LPC) mode, the identifica-
tion Inputs (ID0-ID2) can address up to 8 memo-
ries on a bus. In the LPC mode, the ID3 pin is
Reserved for Future Use (RFU). The value on ad-
dress A19-A21 is compared to the hardware strap-
ping on the ID0-ID2 pins to select the memory that
is being addressed. For an address bit to be ‘1’,
the corresponding ID pin can be left floating or
driven Low, V
resistor, with a value of R
be ‘0’, the corresponding ID pin must be driven
High, V
I
details, see
10/52
LI2
through the pin, as specified in
IH
IL
Communication
(and there will be a leakage current of
, on the rising edge of the Clock, a new
Figure 2.
Table
section and the
IL
Supply Signal Descriptions
(again, with the internal pull-down
IL
IH
, during a bus operation then the
, the current bus operation is ei-
5..
LI2
and
through the pin).
IL
Table
). For an address bit to
IH
(and there will be a
Frame
IL
1..
). A ‘1’ is signified
Address/Address
Table
24.). For
section.
(FWH4/
IL
sec-
, or
General Purpose Inputs (GPI0-GPI4). The
General Purpose Inputs can be used as digital in-
puts for the CPU to read, with their contents being
available in the General Purpose Inputs Register.
The pins must have stable data throughout the en-
tire cycle that reads the General Purpose Input
Register. These pins should be driven Low, V
High, V
Interface Configuration (IC). The Interface Con-
figuration input selects whether the FWH/LPC in-
terface or the Address/Address Multiplexed (A/A
Mux) Interface is used. The state of the Interface
Configuration, IC, should not be changed during
operation of the memory device, except for select-
ing the desired interface in the period before pow-
er-up or during a Reset.
To select the FWH/LPC Interface, the Interface
Configuration pin should be left to float or driven
Low, V
plexed (A/A Mux) Interface, the pin should be driv-
en High, V
included with a value of R
current of I
Interface Reset (RP). The Interface Reset (RP)
input is used to reset the device. When Interface
Reset (RP) is driven Low, V
Reset mode (the outputs go to high impedance,
and the current consumption is minimized). When
RP is driven High, V
eration. After exiting Reset mode, the memory en-
ters Read mode.
CPU Reset (INIT). The CPU Reset, INIT, signal
is used to Reset the device when the CPU is reset.
It behaves identically to Interface Reset, RP, and
the internal Reset line is the logical OR (electrical
AND) of RP and INIT.
Clock (CLK). The Clock, CLK, input is used to
clock the signals in and out of the Input/Output
Communication Pins, FWH0/LAD0-FWH3/LAD3.
The Clock conforms to the PCI specification.
Top Block Lock (TBL). The Top Block Lock in-
put is used to prevent the Top Block (Block 7) from
being changed. When Top Block Lock, TBL, is
driven Low, V
the Top Block have no effect, regardless of the
state of the Lock Register. When Top Block Lock,
TBL, is driven High, V
is determined by the Lock Register. The state of
Top Block Lock, TBL, does not affect the protec-
tion of the Main Blocks (Blocks 0 to 6). For details,
see
Top Block Lock, TBL, must be set prior to a pro-
gram or erase operation being initiated, and must
not be changed until the operation has completed,
otherwise unpredictable results may occur. Simi-
larly, unpredictable behavior is possible if WP is
APPENDIX
IH
IL
. To select the Address/Address Multi-
, and must not be left floating.
LI2
IH
through each pin when pulled to V
. An internal pull-down resistor is
IL
, program and erase operations in
A..
IH
IH
, the device is in normal op-
, the protection of the Block
IL
; there will be a leakage
IL
, the memory is in
IL,
IH
or
.