CD43-100 Linear Technology, CD43-100 Datasheet - Page 7

• Manufacturer Part Number: CD43-100
• Description: Dual Micropower DC/DC Converter with Positive and Negative Outputs
• Manufacturer: Linear Technology

APPLICATIO S I FOR ATIO
Setting the Output Voltages
Set the output voltage for Switcher 1 (negative output
voltage ) by choosing the appropriate values for feedback
resistors R1 and R2.
Set the output voltage for Switcher 2 (positive output
voltage) by choosing the appropriate values for feedback
resistors R1B and R2B (see Figure 1).
Diode Selection
For most LT1945 applications, the Zetex ZHCS400 sur-
face mount Schottky diode (0.4A, 40V) is an ideal choice.
Schottky diodes, with their low forward voltage drop and
PACKAGE DESCRIPTIO
(.0120 .0015)
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.305 0.038
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
R
R B R B
TYP
1
1
(.206)
5.23
MIN
1 23
RECOMMENDED SOLDER PAD LAYOUT
.
R
2
V
2
OUT
V
1 23
V
.
– .
OUT
1 23
2 10
U
•
V
V
1
6
U
0.889 0.127
(.035 .005)
(.126 – .136)
3.2 – 3.45
(.0197)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
0.50
BSC
W
U
GAUGE PLANE
(.007)
0.18
(Reference LTC DWG # 05-08-1661)
U
10-Lead Plastic MSOP
(.010)
MS Package
0.254
fast switching speed, are the best match for the LT1945.
The Motorola MBR0520, MBR0530, or MBR0540 can also
be used. Many different manufacturers make equivalent
parts, but make sure that the component is rated to handle
at least 0.35A.
Lowering Output Voltage Ripple
Using low ESR capacitors will help minimize the output
ripple voltage, but proper selection of the inductor and the
output capacitor also plays a big role. The LT1945 pro-
vides energy to the load in bursts by ramping up the
inductor current, then delivering that current to the load.
If too large of an inductor value or too small of a capacitor
value is used, the output ripple voltage will increase
because the capacitor will be slightly overcharged each
burst cycle. To reduce the output ripple, increase the
output capacitor value or add a 4.7pF feed-forward capaci-
tor in the feedback network of the LT1945 (see the circuits
in the Typical Applications section). Adding this small,
inexpensive 4.7pF capacitor will greatly reduce the output
voltage ripple.
DETAIL “A”
DETAIL “A”
0 – 6 TYP
(.021 .006)
0.53 0.01
SEATING
PLANE
(.118 .004)
3.00 0.102
(.007 – .011)
(.192 .004)
0.17 – 0.27
(NOTE 3)
4.88 0.10
(.043)
MAX
1.10
(.0197)
0.50
10
TYP
1 2 3 4 5
9
8
7 6
LT1945
(.118 .004)
3.00 0.102
(.0196 .003)
0.497 0.076
(.034)
0.86
NOTE 4
REF
(.005 .002)
0.13 0.05
MSOP (MS) 0402
REF
7
1945f