1207A ON Semiconductor, 1207A Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
1207A
Manufacturer Part Number
1207A
Description
Search -----> NCP1207A
Manufacturer
ON Semiconductor
Datasheet
1.1207A.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
1207A
Manufacturer:
ON/安森美
Quantity:
20 000
www.DataSheet.co.kr
consumption and the MOSFET’s gate charge Qg. If we
select a MOSFET like the MTP2N60E, Qg equals 22 nC
(max). With a maximum switching frequency selected at
75 kHz, the average power necessary to drive the MOSFET
(excluding the driver efficiency and neglecting various
voltage drops) is:
V
consumption at no−load will therefore heavily rely on the
internal IC consumption plus the above driving current
(altered by the driver’s efficiency). Suppose that the IC is
supplied from a 350 VDC line. The current flowing through
pin 8 is a direct image of the NCP1207A consumption
(neglecting the switching losses of the HV current source).
If I
dissipated (lost) by the IC is simply: 350 V x 2.3 mA =
805 mW. For design and reliability reasons, it would be
interested to reduce this source of wasted power that
increase the die temperature. This can be achieved by using
different methods:
CC
MAINS
The DSS behavior actually depends on the internal IC
To obtain the output current, simply divide this result by
Fsw Qg V
CC2
Figure 13. A simple diode naturally reduces the
: I
1. Use a MOSFET with lower gate charge Qg.
2. Connect pin 8 through a diode (1N4007 typically) to
Fsw = maximum switching frequency
Qg = MOSFET’s gate charge
V
driver
CC
one of the mains input. The average value on pin 8
becomes
example drops to: 223 V x 2.3 mA = 512 mW. If a
resistor is installed between the mains and the diode,
you further force the dissipation to migrate from the
package to the resistor. The resistor value should
account for low−line startups.
equals 2.3 mA @ T
= V
= F
1
GS
SW
CC
average voltage on Pin 8
V mainsPEAK @ 2
level applied to the gate
2
with:
Qg = 1.6 mA. The total standby power
C
p
bulk
HV
J
= 60 C, then the power
. Our power contribution
1
2
3
4
5
1N4007
8
7
6
5
http://onsemi.com
NCP1207A
6
8
Skipping Cycle Mode
when the output power demand drops below a given level.
This is accomplished by monitoring the FB pin. In normal
operation, Pin 2 imposes a peak current accordingly to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this setpoint reaches a
determined level, the IC prevents the current from
decreasing further down and starts to blank the output
pulses: the IC enters the so−called skip cycle mode, also
named controlled burst operation. The power transfer now
depends upon the width of the pulse bunches (Figure 14) and
follows the following formula:
The NCP1207A automatically skips switching cycles
300
200
100
Figure 14. The skip cycle takes place at low peak
1
2
currents which guaranties noise free operation
0
3. Permanently force the V
@ Lp @ Ip
Lp = primary inductance
Fsw = switching frequency within the burst
Ip = peak current at which skip cycle occurs
D
burst
When using Figure 13 option, it is important to check
the absence of any negative ringing that could occur
on pin 8. The resistor in series should help to damp
any parasitic LC network that would ring when
suddenly applying the power to the IC. Also, since
the power disappears during 10 ms (half−wave
rectification), CV
the IC during these holes in the supply
an auxiliary winding. It will automatically
disconnect the internal startup source and the IC will
be fully self−supplied from this winding. Again, the
total power drawn from the mains will significantly
decrease. Make sure the auxiliary voltage never
exceeds the 16 V limit.
RECURRENCE
= burst width / burst recurrence
2
MAX PEAK
CURRENT
@ Fsw @ D burst
WIDTH
CC
should be calculated to supply
with:
CC
level above V
NORMAL CURRENT
MODE OPERATION
CURRENT LIMIT
SKIP CYCLE
CCH
with
Datasheet pdf - http://www.DataSheet4U.net/