CM2225 LITEMAX, CM2225 Datasheet

Page 1

... LITEMAX Sunlight Readable 22” WXGA LCD Display (1st Edition 8/20/2007 ) All information is subject to change without notice. Approved by Checked by David Sharline CM2225 www.DataSheet.co.kr Prepared by River LITEMAX Electronics Inc. 8F-2, No.133, Lane 235, Bau-chiau Rd., Shin-dian City, Taipei County, Taiwan R.O.C. Tel : 886-2-8919-1858 Fax: 886-2-8919-1300 Homepage: http://www ...

Page 2

Record Revision Version and Date Page Old Description New Description Page 2 Remark ...

Page 3

Contents Record Revision Contents Handling Precautions General Description Overview Features Application General Specificati0ns Mechanical Specifications Absolute Maximum Ratings Absolute Ratings Of Environment Electrical Absolute Ratings TFT LCD Module Backlight Unit Electrical Characteristics TFT LCD Module Ta=25±2ºC Backlight Unit Block Diagram ...

Page 4

Handling Precautions 1) Since front polarizer is easily damaged, be extremely careful when handling panel sure to turn off power supply when inserting or disconnecting from input connectors. 3) Wipe off water immediately. Long contact with water may ...

Page 5

General Description Overview The M220Z1-L01 model inch wide TFT-LCD module with a 4-CCFL Backlight Unit and a 30-pin 2ch-LVDS interface. This module supports 1680 x 1050 WSXGA wide screen) mode and displays up to 16.7 millions colors. ...

Page 6

Absolute Maximum Ratings Absolute Ratings Of Environment Item Symbol Storage Temperature T Operating Ambient Temperature T S Shock (Non-Operating) Vibration (Non-Operating) V LCD Cell Life Time L Note (1) Temperature and relative humidity range is shown in the figure below. ...

Page 7

Electrical Absolute Ratings TFT LCD Module Item Symbol Power Supply Vcc Voltage Logic Input Voltage V IN Backlight Unit Item Symbol V Lamp Voltage L I Lamp Current L Lamp Frequency F L Note (1) Permanent damage might occur if ...

Page 8

Electrical Characteristics TFT LCD Module Ta=25±2ºC Parameter Power Supply Voltage Ripple Voltage Rush Current White Black Power Supply f = 75Hz, V Current Vcc=4.5V LVDS differential input voltage LVDS common input voltage Note (1) The module is recommended to operate ...

Page 9

Note (3) The specified power supply current is under the conditions at Vcc = 5 ± 2 º Hz, whereas a power dissipation check pattern below is displayed. v Note (4) The specified ...

Page 10

Backlight Unit Parameter Symbol . Min. Lamp Input V L 738 Voltage Lamp Current Lamp Turn Voltage - Operating Frequency L BL Lamp Life Time 50000 Power ...

Page 11

The output of the inverter must have symmetrical (negative and positive) voltage waveform and symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency ...

Page 12

Block Diagram TFT LCD Module Backlight Unit www.DataSheet.co.kr Page 12 Datasheet pdf - http://www.DataSheet4U.net/ ...

Page 13

Input Terminal Pin Assignment TFT LCD Module Pin Name Description 1 RXO0- Negative LVDS differential data input. Channel O0 (odd) 2 RXO0+ Positive LVDS differential data input. Channel O0 (odd) 3 RXO1- Negative LVDS differential data input. Channel O1 (odd) ...

Page 14

SELLVDS = Low or Open LVDS output LVDS Channel E0 Data order LVDS output LVDS Channel E1 Data order LVDS output LVDS Channel E2 Data order LVDS output LVDS Channel E3 Data order LVDS output LVDS Channel O0 Data order ...

Page 15

Backlight Unit Pin Symbol Note (1) Note (1) Connector Part No.: JST-BHSR-02VS-1 or equivalent Note (2) Note (2) User’s connector Part No.: JST-SM02B-BHSS-1-TB (JST) or equivalent Color Data Input Assignment The brightness ...

Page 16

Interface Timing 6.1 INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Frequency Fc Period Tc LVDS Clock High Time Tch Low Time Tcl Setup Tlvs LVDS ...

Page 17

Power On/Off Sequence To prevent a latch- operation of LCD module, the power on/off sequence should follow the conditions shown in the following diagram. Note. (1) The supply voltage of the external system for the module input should ...

Page 18

Optical Characteristics Test Conditions Item Symbol Ambient Temperature Ta Ambient Humidity Ha Supply Voltage V CC According to typical value in "3. ELECTRICAL Input Signal CHARACTERISTICS" Inverter Current I L Inverter Driving Frequency F L Inverter SUMIDA H05 5307 Optical ...

Page 19

Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L0 L255: Luminance of gray level 255 L 0: Luminance of gray level ...

Page 20

Note (4) Definition of Luminance of White (L at center point (7) L (x) is corresponding to the luminance of the point Figure in Note (6). Note (5) Measurement Setup: The LCD module should ...

Page 21

Datasheet pdf - http://www.DataSheet4U.net/ ...

Page 22

Datasheet pdf - http://www.DataSheet4U.net/ ...