MP1519 MPS, MP1519 Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
MP1519
Manufacturer Part Number
MP1519
Description
High Efficiency Charge Pump 4 White LED Driver
Manufacturer
MPS
Datasheet
1.MP1519.pdf
(8 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MP1519
Manufacturer:
MPS
Quantity:
20 000
Company:
Part Number:
MP1519DQ-LF-Z
Manufacturer:
RICOH
Quantity:
306
Part Number:
MP1519DQ-LF-Z
Manufacturer:
MPS
Quantity:
20 000
Company:
Part Number:
MP1519DQ-LFZ
Manufacturer:
MPS
Quantity:
164
Company:
Part Number:
MP1519DQ-Z
Manufacturer:
BCD
Quantity:
64 562
Part Number:
MP1519DQ-Z
Manufacturer:
MPS
Quantity:
20 000
Part Number:
MP1519DQL-LF-Z
Manufacturer:
MPS
Quantity:
20 000
Part Number:
MP1519DS-LF-Z
Manufacturer:
MPS/美国芯源
Quantity:
20 000
PIN FUNCTIONS
MP1519 Rev. 1.9
7/27/2006
Pin #
3, 10
5, 13
11
12
14
15
16
1
2
4
6
7
8
9
Name Description
LEDC
RADJ
LED4
BATT
LED1
LED2
LED3
GND
C1A
C2A
C1B
C2B
NC
EN
TM
#4 LED Driver. Connect the #4 LED between LED4 and LEDC, with the anode at LED4, and
the cathode at LEDC. If the #4 LED is not used, leave LED4 unconnected.
No Connect.
Ground.
Charge Pump Capacitor #1 Positive Node. Connect the positive side of the #1 charge pump
capacitor to C1A. Typical applications require C1 to be 1µF.
Battery Power Input. Connect the 2.5V to 5.5V input source between BATT and GND. Bypass
BATT to GND with a 1µF or greater capacitor.
Charge Pump Capacitor #2 Positive Node. Connect the positive side of the #2 charge pump
capacitor to C2A. Typical applications require C2 to be 1µF.
Charge Pump Capacitor #1 Negative Node. Connect the negative side of the #1 charge pump
capacitor to C1B.
LED Common for the Cathodes. Connect the cathodes of the LEDs to LEDC and to a 4.7µF
bypass capacitor. Do not connect to any other ground, supply or pin.
Note: Exposed pad on backside is connected to this pin. Do Not Ground.
Charge Pump Capacitor #2 Negative Node. Connect the negative side of the #2 charge pump
capacitor to C2B.
LED Current Adjust Input. Connect a resistor between RADJ and GND to set the LED current.
All of the LEDs regulate at the same current. See Setting the LED Current.
Enable Input. Drive EN high to turn on the MP1519, drive EN low to shutdown the MP1519. To
use burst-mode brightness control, drive EN with a PWM signal. See Burst Mode Dimming.
#1 LED Driver. Connect the #1 LED between LED1 and LEDC, with the anode at LED1, and
the cathode at LEDC. If the #1 LED is not used, leave LED1 unconnected.
#2 LED Driver. Connect the #2 LED between LED2 and LEDC, with the anode at LED2, and
the cathode at LEDC. If the #2 LED is not used, leave LED2 unconnected.
#3 LED Driver. Connect the #3 LED between LED3 and LEDC, with the anode at LED3, and
the cathode at LEDC. If the #3 LED is not used, leave LED3 unconnected.
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
MP1519 – 1X, 1.5X, 2X CHARGE PUMP 4 WHITE LED DRIVER
© 2006 MPS. All Rights Reserved.
www.MonolithicPower.com
4