MB3763 Fujitsu Microelectronics, Inc., MB3763 Datasheet
MB3763
Available stocks
Related parts for MB3763
MB3763 Summary of contents
Page 1
... MB3763 DESCRIPTION Fujitsu’s MB3763 Motor Driver with forward/reverse control capability, is used in applications such as the front- loading mechanism in video tape, or the auto-reverse tape deck, driven by a TTL signal. The MB3763 has 150 mA drive units and braking capability with TTL control. FEATURES • ...
Page 2
... MB3763 PIN ASSIGNMENT BLOCK DIAGRAM A-V CC A-OUT 2 (TOP VIEW A-IN A-OUT GND GND B B-OUT (DIP-8P-M01) (FPT-8P-M01) Input Logic A-IN GND B-IN B-V CC B-OUT ...
Page 3
... Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. Rating Min –20 C –55 Symbol Min 2 MB3763 (Ta = +25 C) Unit Max 180 (330 1.2 A 560 +75 C +125 C Value Unit Max 150 (300* 1 ...
Page 4
... MB3763 ELECTRICAL CHARACTERISTICS Parameter Symbol Standby supply current I CC0 I CC1 Power supply current I CC2 I CC3 Output high voltage V OH Output low voltage V OL Output saturation voltage V SAT Input current I IH Input switching T OFF prohibition time 4 Condition Min — ...
Page 5
... Notes: 1: 2.4V 0: 0.4V , the supply current is still less than or equal to 1 mA. CC Control Block Diagram A-IN B- Control Logic Q2 Q4 GND Output mode B-IN A-OUT B-OUT — MB3763 B-V CC B-OUT Operation L short (Brake) H Forward L Reverse — Open (Standby) 5 ...
Page 6
... MB3763 TYPICAL APPLICATION 1 k LOGIC CONTROLLER 1 k Note: In the case the control voltage is input when the power supply voltage is not applied because of the time lag between those two voltages, excess current flows into IC from the input terminals. In this case, please connect a resistor ( serially to input pin in order to prevent excess current flow. ...
Page 7
... Output Current I (mA) O Power Supply Voltage vs. Power Supply Current 500 600 0 Power Supply Voltage V 4.0 3.5 3 2.5 2.0 1.5 1.0 0 500 600 MB3763 I CC3 2 CC1 (V) CC Input Voltage vs. Input Current ...
Page 8
... P-SOP 0.8 0.6 P-DIP/ P-SOP 0.4 0 Temperature ORDERING INFORMATION Part number MB3763 MB3763PF Duty = 50% P-SOP's value is measured on the ceramic board (3 3 0.05 cm) Maximum power dissipation must be kept. 120 Package 8-pin plastic DIP (DIP-8P-M01) 8-pin plastic SOP (FPT-8P-M01) ...
Page 9
... FUJITSU LIMITED D08006S-2C-3 C 6.20±0.25 (.244±.010) 0.51(.020)MIN 0.25±0.05 (.010±.002) 0.46±0.08 (.018±.003) +0.30 1.52 –0 +.012 .060 –0 2.54(.100) TYP MB3763 15°MAX 7.62(.300) TYP Dimensions in mm (inches) (Continued) 9 ...
Page 10
... MB3763 (Continued) 8-pin plastic SOP (FPT-8P-M01) +0.25 +.010 6.35 .250 –0.20 –.008 INDEX 1.27(.050) TYP 3.81(.150)REF "A" 0.10(.004) 2000 FUJITSU LIMITED F08002S-4C 5.30±0.30 7.80±0.40 (.209±.012) (.307±.016) 0.45±0.10 Ø0.13(.005) M (.018±.004) 2.25(.089)MAX (Mounting height) ...
Page 11
... MB3763 FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, ...