D207RU MicroPower Direct, D207RU Datasheet - Page 2

• Manufacturer Part Number: D207RU
• Description: Miniature SIP, 2W Ultra-wide 4:1 Input Dc/dc Converters
• Manufacturer: MicroPower Direct

Model Selection Guide
Notes:
1. When measuring output ripple, it is recommended that an external
2. Transient recovery is measured to within a 1% error band for a
3. Operation at no-load will not damage these units. However, they
4. Dual output units may be connected to provide a 10 VDC, 24 VDC,
5. The converter should be connected to a low ac-impedance source.
6. The optional remote
7. It is recommended that a fuse be used on the input of a power sup-
Capacitive Load
D201RU
D202RU
D203RU
D204RU
D205RU
D206RU
D207RU
D211RU
D212RU
D213RU
D214RU
D215RU
D216RU
D217RU
Number
Note: For dual output
units, Cap load is given for
each output.
Output (VDC)
Model
0.47 μF ceramic capacitor be placed from the +Vout pin to the
-Vout pin for single output units and from each output to common
for dual output units. For noise sensitive applications, the use of
3.3 μF capacitors will reduce the output ripple.
load step change of 75% to 100%.
may not meet all specifi cations.
or 30 VDC output. To do this, connect the load across the positive
(+Vout) and negative (-Vout) outputs and fl oat the output com-
mon.
An input source with a highly inductive impedance may affect
the stability of the converter. In applications where the converter
output loading is high and input power is supplied over long lines,
it may be necessary to use a capacitor on the input to insure start-
up.
In this case, it is recommended that a low ESR (ESR <1.0Ω at 100
kHz) capacitor be mounted close to the converter. For all models,
it is recommended a 1.5 μF be used.
on/off control pin
is referenced to
the
The standby input
current is typically
0 . 1 m A ( 0 . 2 m a
maximum).
ply for protection. See the table above for the correct rating.
±12.0
±15.0
±5.0
12.0
15.0
3.3
5.0
Nominal
-Vin pin.
Voltage (VDC)
24
24
24
24
24
24
24
48
48
48
48
48
48
48
μF Max
2,200
1,000
170
110
470
100
292 Page Street Ste D Stoughton, MA 02072
47
MicroPower Direct
In. Current (on)
In. Current (off)
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
18.0 - 75.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
9.0 - 36.0
Mechanical Notes:
•
•
Range
All dimensions are typical in inch es (mm)
Tolerance x.xx = ±0.01 (±0.25)
Off
On
Input
Pin Connections
NF = No Connection
Pin
1
2
3
6
7
8
9
Full-Load
<0.6 VDC to Open Circuit
110
106
105
114
108
106
2.7 VDC
97
49
58
54
54
60
55
55
Current (mA)
Min
Single
+Vout
-Vout
www.micropowerdirect.com
Remote ON/OFF
+Vin
-Vin
NC
NC
No-Load
20
20
20
20
20
20
20
15
15
15
15
15
15
15
Common
15.0 VDC
+Vout
-1 mA
-Vout
1 mA
Dual
+Vin
Max
-Vin
NC
Voltage
±12.0
±15.0
±12.0
±15.0
(VDC)
±5.0
±5.0
12.0
15.0
12.0
15.0
3.3
5.0
3.3
5.0
Derating Curve
Mechanical Dimensions
(mA, Max)
±200.0
±200.0
•
Current
500.0
400.0
167.0
134.0
±83.0
±67.0
500.0
400.0
167.0
134.0
±83.0
±67.0
Output
TEL: [phone]
(mA, Min)
Current
125.0
100.0
±50.0
±21.0
±17.0
125.0
100.0
±50.0
±21.0
±17.0
42.0
33.0
42.0
33.0
Current (mA)
•
Refl ected
FAX: [phone]
Ripple
300
300
300
300
300
300
300
600
600
600
600
600
600
600
Effi ciency
(%, Typ)
71
76
79
80
73
77
79
70
72
78
78
70
76
76
•
E-Mail: [e-mail]
Fuse Rating
Slow-Blow
(mA)
350
350
350
350
350
350
350
135
135
135
135
135
135
135