MAX1480 Maxim, MAX1480 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
MAX1480
Manufacturer Part Number
MAX1480
Description
Complete / Isolated RS-485/RS-422 Data Interface
Manufacturer
Maxim
Datasheet
1.MAX1480.pdf
(20 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX14800CCM+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX14800CCM+T
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX14801CCM+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX14801CCM+T
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX14802CCM+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
MAX14803CCM+T
Manufacturer:
MAXIM
Quantity:
1 000
Company:
Part Number:
MAX14808ETK
Manufacturer:
MAX
Quantity:
453
Company:
Part Number:
MAX14808ETK+T
Manufacturer:
MAXIM
Quantity:
10
The MAX1480A/MAX1480B/MAX1480C/MAX1490A/
MAX1490B are complete, electrically isolated, RS-485/
RS-422 data-communications interface solutions.
Transceivers, optocouplers, a power driver, and a
transformer in one standard 28-pin DIP package (24-
pin for the MAX1490A/B) provide a complete interface.
Signals and power are internally transported across the
isolation barrier (Figures 1, 2). Power is transferred from
the logic side (non-isolated side) to the isolated side of
the barrier through a center-tapped transformer.
Signals cross the barrier through high-speed optocou-
plers. A single +5V supply on the logic side powers
both sides of the interface. The MAX1480A/B/C offer
half-duplex communications while the MAX1490A/B
feature full-duplex communication. The functional
input/output relationships are shown in Tables 3–6.
The MAX1480B/MAX1480C/MAX1490B feature reduced-
slew-rate drivers that minimize EMI and reduce reflec-
tions caused by improperly terminated cables, allowing
error-free transmission at data rates up to 250kbps. The
MAX1480A/MAX1490A driver slew rate is not limited,
allowing transmission rates up to 2.5Mbps.
The MAX1480B/MAX1480C/MAX1490B shutdown feature
reduces supply current to as low as 0.2µA by using the
SD pin (see Low-Power Shutdown Mode section).
Complete, Isolated RS-485/RS-422
Data Interface
___________________________________________________Pin Description (continued)
Note: For DE
10
MAX1480A/B/C
_______________Detailed Description
PINS ON THE ISOLATED RS-485/RS-422 SIDE (continued)
27, 28
______________________________________________________________________________________
21
22
23
24
25
26
Figure 2 for MAX1490A/B).
—
—
—
—
´
PIN
and DI
MAX1490A/B
´
23, 24
pin descriptions, see Detailed Block Diagram and Typical Application Circuit (Figure 1 for MAX1480A/B/C,
17
18
19
20
21
22
—
—
—
—
ISO RO DRV
ISO DE IN
AC2, AC1
ISO DI IN
ISO V
NAME
Y
Z
B
A
A
B
CC1
Noninverting Driver Output
Inverting Driver Output
Inverting Receiver Input
Noninverting Receiver Input
Isolated Driver-Enable Input. Connect to ISO DE DRV for normal operation.
Isolated Driver Input. Connect to ISO DI DRV for normal operation.
Noninverting Driver Output and Noninverting Receiver Input
Isolated Receiver-Output Drive. Connect to ISO RO LED through a resistor
(Table 1 of Figure 1 for MAX1480A/B/C, Table 2 of Figure 2 for MAX1490A/B).
Inverting Driver Output and Inverting Receiver Input
Isolated Supply Voltage Source
Internal Connections. Leave these pins unconnected.
Use the FS pin to select between high and low switching
frequencies for the isolated power driver. The driver
switches at the lower frequency 535kHz when FS is low,
and at the higher frequency 725kHz when FS is high. The
FS pin has a weak internal pull-up that switches the
device to the high-frequency mode when FS is left
unconnected. With FS high or open, no-load supply
current is reduced by approximately 4mA, and by up to
8mA when fully loaded. For optimal performance and
minimal supply current, connect FS to V
unconnected.
Drivers are short-circuit current limited and are protect-
ed against excessive power dissipation by thermal
shutdown circuitry that puts the driver outputs into a
high-impedance state. The receiver input has a fail-safe
feature that guarantees a logic-high RO (logic-low RO)
output if the input is open circuit.
On the MAX1480A/B/C, the driver outputs are enabled
by bringing DE
0.2µs for the MAX1480A, 35µs for the MAX1480B, and
0.5µs for the MAX1480C. Allow time for the devices to be
enabled before sending data (see the Driver Enable
Time vs. Temperature graph in the Typical Operating
Characteristics ). When enabled, driver outputs function
as line drivers. Driver outputs are high impedance when
DE
tion as line receivers.
´
is low. While outputs are high impedance, they func-
FUNCTION
´
high. Driver-enable times are typically
CC_
or leave