BMP-5/3.338W Datel, Inc., BMP-5/3.338W Datasheet - Page 3

• Manufacturer Part Number: BMP-5/3.338W
• Manufacturer: Datel, Inc.

3 5 W , D U A L O U T P U T D C / D C C O N V E R T E R S
Performance/Functional Specifi cations
Typical @ T
Input Voltage Range:
Overvoltage Shutdown:
Input Current:
Input Refl ected Ripple Current:
Internal Input Filter Type
Reverse-Polarity Protection:
On/Off Control (Pin 5):
V
Minimum Loading Per Specifi cation
Ripple/Noise (20MHz BW)
Line/Load Regulation
Effi ciency
Trim Range +5V Output
Isolation Voltage:
Isolation Capacitance
Isolation Resistance
Temperature Coeffi cient
Current Limit Inception:
Short Circuit Current:
Overvoltage Protection:
Dynamic Load Response:
Switching Frequency
OUT
D24 Models
D48 Models
D24 Models
D48 Models
Normal Operating Conditions
Standby Mode:
Source Impedance
D24 Models
D48 Models
D24 & D48 Models
5V Output
3.3V Output
Input-to-Output
Case-to-Input
Case-to-Output
5V @ 98.5% V
3.3V @ 98.5% V
5V Output
3.3V Output
5V Output
5V (50-100% load step to 3% V
3.3V (50-100% load step to 3% V
Off, OV, Thermal Shutdown
D24 & D48 Models
Accuracy
A
= +25°C under nominal line voltage, balanced "full-load" conditions, unless noted.
OUT
OUT
(3.3V @ 3.5A)
(5V @ 4.7A)
Dynamic Characteristics
Output (continued)
OUT
OUT
)
Output
)
Input
18-36 Volts (24V nominal)
36-75 Volts (48V nominal)
36.4-43.6 Volts (40V nominal)
77-85 Volts (83V nominal)
See Ordering Guide
10mA typical
<0.1 , no external input fi ltering
100mAp-p (typical)
Pi (4.5µF - 10µH - 7.5µF)
1 minute duration, 3A maximum
1 minute duration, 2A maximum
On = open or 2.6V - +V
Off = 0-1.2V, I
±1% maximum
±1.5% maximum
10%
See Ordering Guide
See Ordering Guide
See Ordering Guide
±5%
1500Vdc minimum
1000Vdc minimum
1000Vdc mimimum
470pF
100M
±0.02%/per°C
6-8 Amps
5-8 Amps
10 Amps average, continuous
8 Amps average, continuous
Magnetic feedback/transorb
6.8 volts
300µsec maximum
300µsec maximum
150kHz (±15kHz)
IN
= 1.5mA max.
IN
, I
IN
= 1.5mA max.
3
MTBF
Operating Temperature (Ambient):
Case Temperature:
Storage Temperature
Dimensions
Shielding
Case Connection
Case Material
Pin Material
Weight:
Primary to Secondary Insulation Level
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in the
Performance/Functional Specifi cations Table is not implied, nor recommended.
Input Voltage:
Input Reverse-Polarity Protection
Output Overvoltage Protection
Output Current
Storage Temperature
Lead Temperature (Soldering, 10 sec.)
Without Derating:
With Derating
D24 Models
D48 Models
Maximum Operational
For Thermal Shutdown
D24 Models
D48 Models
All models are specifi ed with no external output capacitors.
See Technical Notes/Graphs for details.
Devices may be ordered with On/Off Control function or a Sync function.
See Part Number Suffi xes and Technical Notes for details.
Applying a voltage to On/Off Control (pin 5) when no input power is applied to the
converter may cause permanent damage.
Output noise may be further reduced with the installation of additional external output
capacitors.
On/Off control is designed to be driven with open collector or by appropriate voltage
levels. Voltages must be referenced to the input return pin (–Input).
Demonstrated MTBF available on request.
D24 Models
D48 Models
+5V Outputs
Absolute Maximum Ratings
Environmental
Physical
42 Volts
88 Volts
Current must be <3A. Brief duration
only. Fusing recommended.
6.8 Volts
Current limited. Maximum current and
short-circuit duration are model
dependent.
–40 to +105°C
+300°C
Bellcore, ground fi xed, full power, +25°C
operating ambient temperature
TBC million hours
TBC million hours
No heat sink
–40 to +50°C
To +100°C (See Derating Curves)
+100°C
+95°C minimum, +105°C maximum
–40 to +120°C
2.04 x 3.04 x 0.55" (51.8 x 77.2 x 14mm)
5-sided
Pin 4
Aluminum, black anodized fi nish
with plastic header
Brass, solder coated
6 ounces (170 grams)
Operational
Basic
BMP Models