ATA5279 ATMEL Corporation, ATA5279 Datasheet - Page 25

no-image

ATA5279

Manufacturer Part Number
ATA5279
Description
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATA5279C
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATA5279C
Quantity:
512
Part Number:
ATA5279C-PLQW
Manufacturer:
ATMEL
Quantity:
1 700
Part Number:
ATA5279C-PLQW
Manufacturer:
ATMEL
Quantity:
8 000
Part Number:
ATA5279C-PLQW
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATA5279N
Manufacturer:
ATMEL
Quantity:
1 980
Part Number:
ATA5279N
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATA5279P
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATA5279P-PLQW
Manufacturer:
ATMEL
Quantity:
3 500
Part Number:
ATA5279P-PLQW
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATA5279PPLQW19
Manufacturer:
AD
Quantity:
7 349
3.9.4
9125A–RKE–04/08
Status Monitor
The status monitor holds all information from the diagnosis stage. In case of an existing fault, all
power stages are disabled. As soon as a fault is stored, an interrupt request (IRQ) to the micro-
controller is generated. This signal is persistent until the status info is polled by the
microcontroller. The entry in the fault register can only be cleared by the Reset Fault command
or a global reset.
There are two different status registers:
The fault register is encoded as follows:
Table 3-6.
The meaning of the bits is described below:
Fault Register
• A general IC status register (requestable by the Get Status Info command)
• A coil-driver related fault register (requestable by the Get Fault Info command)
• D
• T: A temperature shutdown has occurred. Note that there is not necessarily a link between
• F
• F
• F
• F
selected driver can be affected by external faults. Therefore, it is sufficient to store the type of
failure and the corresponding driver number. Refer to
Description” on page 22
the driver number and this fault, as all sensor signals of the chip are OR’ed together.
However, in general, it can be assumed that the last active driver also caused the
overtemperature condition.
current detection unit was not able to find a sinusoidal signal on the VSHS pin although the
LF coil was driven. The reason for this can either be an open load condition or a short-circuit
on the AxN pin towards ground.
this is only the case if there is a high current flowing through the shunt resistor. The typical
reason for this is a short-circuit on the AxN line towards battery. Another possible reason
could be a shorted LF coil.
AxP line. The most typical reason for this is a short-circuit towards ground.
line. The most typical reason for this is a short-circuit towards battery.
03
02
01
00
G
, D
: This bit indicates a missing return line signal during modulation. That means that the
: This bit indicates an excessive positive voltage on the VSHS pin. In normal applications,
: This bit indicates an excessive current through the high-side transistor that drives the
: This bit indicates an excessive current through the low-side transistor that drives the AxP
1..0
: The driver group and number that was active when the fault occurred. Only a
Fault Assignment between Driver Stages and the Fault Registers
for further details on the coding of these bits.
MSB
D
G
D
1
ATA5279 [Preliminary]
D
0
Section 3.9.3 “Driver-related Command
T
F
03
F
02
F
01
LSB
F
00
25

Related parts for ATA5279