ATA6829 ATMEL Corporation, ATA6829 Datasheet - Page 5
ATA6829
Manufacturer Part Number
ATA6829
Description
Dual Triple DMOS Output Driver with Serial Input Control
Manufacturer
ATMEL Corporation
Datasheet
1.ATA6829.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATA6829
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATA6829-T3QY
Manufacturer:
ATMEL
Quantity:
3 500
Part Number:
ATA6829-T3QY
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATA6829-T3QY-71
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
After power-on reset, the input register has the following status:
The following patterns are used to enable internal test modes of the IC. It is not recommended to use these patterns during
normal operation.
4531F–BCD–09/05
Bit 15
Bit 15
H
H
H
SI
H
Bit 14
Bit 14
OCS
H
H
H
H
(OCS)
Bit 13
Bit 13
OLD
H
H
H
H
Bit 12
Bit 12
PH3
H
Table 3-2.
L
L
L
Bit
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
Bit 11
Bit 11
PL3
H
L
L
L
Output (Status)
Bit 10
Status HS1
Status HS2
Status HS3
Status LS1
Status LS2
Status LS3
Bit 10
PH2
Output Data Protocol
Register
H
L
L
L
n. u.
n. u.
n. u.
n. u.
n. u.
n. u.
OVL
PSF
INH
TP
Bit 9
Bit 9
PL2
H
L
L
L
Bit 8
Function
Temperature prewarning: high = warning
Normal operation: high = output is on, low = output is off
Open-load detection: high = open load, low = no open load
(correct load condition is detected if the corresponding output is switched
off); not affected by SRR
Normal operation: high = output is on, low = output is off
Open-load detection: high = open load, low = no open load
(correct load condition is detected if the corresponding output is switched
off); not affected by SRR
Description see LS1
Description see HS1
Description see LS1
Description see HS1
Not used
Not used
Not used
Not used
Not used
Not used
Over-load detected: set high, when at least one output is switched off by
a short-circuit condition or an overtemperature event. Bits 1 to 6 can be
used to detect the affected switch.
(open-load detection bit OLD = high)
Inhibit: this bit is controlled by software (bit SI in input register)
High = standby, low = normal operation
Power-supply fail: undervoltage at pin VS detected
Bit 8
PH1
H
L
L
L
Bit 7
Bit 7
PL1
H
L
L
L
(HS3)
Bit 6
Bit 6
HS3
L
L
L
L
(LS3)
Bit 5
Bit 5
LS3
L
L
L
L
(HS2)
Bit 4
Bit 4
HS2
L
L
L
L
T6819/ATA6829
(LS2)
Bit 3
Bit 3
LS2
L
L
L
L
(HS1)
Bit 2
Bit 2
HS1
L
L
L
L
(LS1)
Bit 1
Bit 1
LS1
L
L
L
L
(SRR)
Bit 0
Bit 0
SRR
L
L
L
L
5