MAX186 Maxim, MAX186 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
MAX186
Manufacturer Part Number
MAX186
Description
Low-Power / 8-Channel / Serial 12-Bit ADCs
Manufacturer
Maxim
Datasheet
1.MAX186.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX1864EEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1864TEEE
Manufacturer:
MAXIM
Quantity:
81
Part Number:
MAX1864TEEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1864TEEE-T
Manufacturer:
ANPEC
Quantity:
3 400
Part Number:
MAX1865EEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX1865TEEP
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX1865TEEP+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Part Number:
MAX1866EUB
Manufacturer:
MAXIM/美信
Quantity:
20 000
The MAX186/MAX188 use a successive-approximation
conversion technique and input track/hold (T/H) circuit-
ry to convert an analog signal to a 12-bit digital output.
A flexible serial interface provides easy interface to
microprocessors. No external hold capacitors are
required. Figure 3 shows the block diagram for the
MAX186/MAX188.
The sampling architecture of the ADC’s analog com-
parator is illustrated in the Equivalent Input Circuit
(Figure 4). In single-ended mode, IN+ is internally
switched to CH0-CH7 and IN- is switched to AGND. In
differential mode, IN+ and IN- are selected from pairs
of CH0/CH1, CH2/CH3, CH4/CH5 and CH6/CH7.
Configure the channels with Table 3 and Table 4.
In differential mode, IN- and IN+ are internally switched
to either one of the analog inputs. This configuration is
pseudo-differential to the effect that only the signal at
IN+ is sampled. The return side (IN-) must remain sta-
ble within ±0.5LSB (±0.1LSB for best results) with
respect to AGND during a conversion. Accomplish this
by connecting a 0.1µF capacitor from AIN- (the select-
ed analog input, respectively) to AGND.
During the acquisition interval, the channel selected as
the positive input (IN+) charges capacitor C
acquisition interval spans three SCLK cycles and ends
on the falling SCLK edge after the last bit of the input
control word has been entered. At the end of the acqui-
sition interval, the T/H switch opens, retaining charge
on C
The conversion interval begins with the input multiplex-
er switching C
negative input (IN-). In single-ended mode, IN- is sim-
ply AGND. This unbalances node ZERO at the input of
the comparator. The capacitive DAC adjusts during the
remainder of the conversion cycle to restore node
ZERO to 0V within the limits of 12-bit resolution. This
action is equivalent to transferring a charge of 16pF x
[(V
capacitive DAC, which in turn forms a digital represen-
tation of the analog input signal.
The T/H enters its tracking mode on the falling clock
edge after the fifth bit of the 8-bit control word has been
shifted in. The T/H enters its hold mode on the falling
clock edge after the eighth bit of the control word has
been shifted in. If the converter is set up for
Low-Power, 8-Channel,
Serial 12-Bit ADCs
8
_______________Detailed Description
IN
_______________________________________________________________________________________
HOLD
+) - (V
as a sample of the signal at IN+.
IN
-)] from C
HOLD
from the positive input (IN+) to the
Pseudo-Differential Input
HOLD
to the binary-weighted
Track/Hold
HOLD
. The
single-ended inputs, IN- is connected to AGND, and
the converter samples the “+” input. If the converter is
set up for differential inputs, IN- connects to the “-”
input, and the difference of
the end of the conversion, the positive input connects
back to IN+, and C
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
the acquisition time lengthens and more time must be
allowed between conversions. Acquisition time is cal-
culated by:
where R
input signal, and t
source impedances below 5k
affect the AC performance of the ADC. Higher source
impedances can be used if an input capacitor is con-
nected to the analog inputs, as shown in Figure 5. Note
that the input capacitor forms an RC filter with the input
source impedance, limiting the ADC’s signal bandwidth.
The ADC’s input tracking circuitry has a 4.5MHz
small-signal bandwidth, so it is possible to digitize
high-speed transient events and measure periodic sig-
nals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Figure 4. Equivalent Input Circuit
SINGLE-ENDED MODE: IN+ = CHO-CH7, IN– = AGND.
DIFFERENTIAL MODE: IN+ AND IN– SELECTED FROM PAIRS OF
AGND
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
VREF
IN
= 5kΩ, R
INPUT
MUX
12-BIT CAPACITIVE DAC
t
AZ
CH0/CH1, CH2/CH3, CH4/CH5, CH6/CH7.
C
SWITCH
–
= 9 x (R
AZ
C
16pF
HOLD
HOLD
TRACK
S
SWITCH
is never less than 1.5µs. Note that
+
= the source impedance of the
T/H
charges to the input signal.
S
10k
R
S
+ R
HOLD
ZERO
|
IN+ - IN-
IN
) x 16pF,
AT THE SAMPLING INSTANT,
THE MUX INPUT SWITCHES
FROM THE SELECTED IN+
CHANNEL TO THE SELECTED
IN– CHANNEL.
Input Bandwidth
do not significantly
COMPARATOR
|
is sampled. At