MAX218 Maxim, MAX218 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
MAX218
Manufacturer Part Number
MAX218
Description
1.8V to 4.25V-Powered / True RS-232 Dual Transceiver
Manufacturer
Maxim
Datasheet
1.MAX218.pdf
(8 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX2181AETE/V+T
Manufacturer:
MAXIM
Quantity:
4
Company:
Part Number:
MAX218CAP
Manufacturer:
MAXIM
Quantity:
5 510
Part Number:
MAX218CAP
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX218CAP+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX218CPP+
Manufacturer:
Maxim
Quantity:
74
Part Number:
MAX218CWI
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX218CWP
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX218CWP+
Manufacturer:
NXP
Quantity:
2 094
Part Number:
MAX218CWP+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX218EAP
Manufacturer:
MAXIM
Quantity:
5 510
The following suggestions will help you get maximum
life out of your batteries.
Shut the MAX218 down when it is not being used for
transmission. The receivers can remain active when
the MAX218 is shut down, to alert your system to exter-
nal activity.
Transmit at the highest practical data rate. Although
this raises the supply current while transmission is in
progress, the transmission will be over sooner. As long
as the MAX218 is shut down as soon as each transmis-
sion ends, this practice will save energy.
Operate your whole system from the raw battery volt-
age rather than suffer the losses of a regulator or DC-
DC converter. If this is not possible, but your system is
powered from two cells and employs a 3V DC-DC con-
verter to generate the main logic supply, use the circuit
of Figure 2. This circuit draws most of the MAX218’s
Figure 2. Operating from Unregulated and Regulated Supplies
CONVERTER
MAX878
MAX756
MAX856
DC-DC
3V
OR
OR
ON/OFF
ENABLE
0.1 F
1 F
C5
C4
_______________________________________________________________________________________
10
3
6
7
8
9
SHDN
T1IN
T2IN
R1OUT
R2OUT
V
15 H
CC
EN
Low-Power Operation
4
1
LX
MAX218
1N6050
T1
T2
D1
R1
R2
19
V+
GND
T1OUT
T2OUT
5, 17, 20
R1IN
R2IN
C1+
C1-
V-
15
18
16
14
13
12
11
True RS-232 Dual Transceiver
1 F
1 F
C2
C3
0.47 F
C1
1.8V to 4.25V-Powered,
power straight from the battery, but still provides logic-
level compatibility with the 3V logic.
Keep communications cables short to minimize capaci-
tive loading. Lowering the capacitive loading on the
transmitter outputs reduces the MAX218’s power con-
sumption. Using short, low-capacitance cable also
helps transmission at the highest data rates.
Keep the S
the MAX218, and take S
risen above about 1.5V. This avoids active operation at
very low voltages, where currents of up to 150mA can be
drawn. This is especially important with systems pow-
ered from rechargeable cells; if S
cells are being trickle charged from a deep discharge,
the MAX218 could draw a significant amount of the
charging current until the battery voltage rises above
1.5V.
The Pin Configuration shows pin 2 as N.C. (no con-
nect). Early samples had a bypass capacitor for the
internal reference connected to pin 2, which was
labeled REF. This bypass capacitor proved to be
unnecessary and the connection has been omitted. Pin
2 may now be connected to ground, left open, or
bypassed to GND with a capacitor.
RS-232 circuits consume much of their power because
the EIA/TIA-232E standard demands that the transmit-
ters deliver at least 5V to receivers with impedances
that can be as low as 3kΩ. For applications where
power consumption is critical, the EIA/TIA-562 standard
provides an alternative.
EIA/TIA-562 transmitter output voltage levels need only
reach ±3.7V, and because they have to drive the same
3kΩ receiver loads, the total power consumption is con-
siderably reduced. Since the EIA/TIA-232E and
EIA/TIA-562 receiver input voltage thresholds are the
same, interoperability between EIA/TIA-232E and
EIA/TIA-562 devices is guaranteed. Maxim’s MAX560
and MAX561 are EIA/TIA-562 transceivers that operate
on a single supply from 3.0V to 3.6V, and the MAX562
transceiver operates from 2.7V to 5.25V while produc-
ing EIA/TIA-562 levels.
_____________EIA/TIA-562 Standards
—
H
—
D
—
N
–
pin low while power is being applied to
—
H
—
D
—
Pin Configuration Change
EIA/TIA-232E and
N
–
high only after V
—
H
—
D
—
N
–
is high while the
CC
has
7