FT232R Future Technology Devices Intl Ltd., FT232R Datasheet - Page 23
![no-image](/images/no-image-200.jpg)
FT232R
Manufacturer Part Number
FT232R
Description
Manufacturer
Future Technology Devices Intl Ltd.
Datasheet
1.FT232R.pdf
(28 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FT232RL
Manufacturer:
FTDI
Quantity:
50 000
Part Number:
FT232RL
Manufacturer:
FTDI
Quantity:
20 000
Company:
Part Number:
FT232RL-R
Manufacturer:
IR
Quantity:
3 001
Company:
Part Number:
FT232RL-REEL
Manufacturer:
FTDI
Quantity:
12 000
Company:
Part Number:
FT232RL-REEL
Manufacturer:
FTDI
Quantity:
120 383
Part Number:
FT232RL-REEL
Manufacturer:
FTDI
Quantity:
20 000
Company:
Part Number:
FT232RL.
Manufacturer:
FTDI
Quantity:
15 000
Part Number:
FT232RQ
Manufacturer:
FTDI
Quantity:
20 000
Figure 14 - Example USB to RS485 Converter Configuration
Figure 14 illustrates how to connect the FT232R’s UART interface to a TTL – RS485 Level Converter I.C. to make a
USB to RS485 converter. This example uses the Sipex SP481 device but there are similar parts available from Maxim
and Analog Devices amongst others. The SP481 is a RS485 device in a compact 8 pin SOP package. It has separate
enables on both the transmitter and receiver. With RS485, the transmitter is only enabled when a character is being
transmitted from the UART. The TXDEN signal CBUS pin option on the FT232R is provided for exactly this purpose
and so the transmitter enable is wired to CBUS2 which has been configured as TXDEN. Similarly, CBUS3 has been
configured as PWREN#. This signal is used to control the SP481’s receiver enable. The receiver enable is active low,
so it is wired to the PWREN# pin to disable the receiver when in USB suspend mode. CBUS2 = TXDEN and CBUS3 =
PWREN# are the default device configurations of these pins. See
RS485 is a multi-drop network – i.e. many devices can communicate with each other over a single two wire cable
connection. The RS485 cable requires to be terminated at each end of the cable. A link is provided to allow the cable
to be terminated if the device is physically positioned at either end of the cable.
In this example the data transmitted by the FT232R is also received by the device that is transmitting. This is a
common feature of RS485 and requires the application software to remove the transmitted data from the received
data stream. With the FT232R it is possible to do this entirely in hardware – simply modify the schematic so that RXD
of the FT232R is the logical OR of the SP481 receiver output with TXDEN using an HC32 or similar logic gate.
FT232R USB UART I.C. Datasheet Version 1.02
SHIELD
5
8.2 USB to RS485 Converter Configuration
1
2
3
4
10nF
100nF
+
Ferrite
Bead
4.7uF
+
Vcc
Vcc
100nF
VCC
USBDM
USBDP
VCCIO
RESET#
OSCI
OSCO
3V3OUT
NC
NC
A
G
N
D
FT232R
G
N
D
G
N
D
Section
G
N
D
T
E
S
T
CBUS0
CBUS1
CBUS2
TXDEN#
CBUS3
CBUS4
© Future Technology Devices International Ltd. 2005
DCD#
DTR#
DSR#
10.
RTS#
CTS#
RXD
TXD
RI#
PWREN#
RXD
TXD
3
4
1
2
RS485 LEVEL
CONVERTER
Vcc
SP481
5
GPIO1
GPIO4
GPIO0
7
6
120R
Link
GND
SHIELD
10
DB9M