MAX5069A Maxim Integrated, MAX5069A Datasheet - Page 3

• Manufacturer Part Number: MAX5069A
• Description: MAX5069A Evaluation Kit
• Manufacturer: Maxim Integrated

Note: Indicate that you are using the MAX5069A when contacting these component suppliers.
Required Equipment
•
•
•
•
•
The MAX5069A EV kit is fully assembled and tested.
Follow these steps to verify board operation. Do not
turn on the power supply until all connections are
completed.
DESIGNATION
AVX
CEL/NEC; California Eastern Laboratories
Central Semiconductor
Coilcraft
Cooper-Coiltronics
International Rectifier
IRC
Murata
Sanyo Electronic Device
TDK
Vishay
36V to 72V power supply capable of providing up
to 6A
20A electronic load e.g., HP 6060B
Voltmeter
330µF, 100V bulk storage capacitor to be connected
to the input terminals of the EV kit
A fan to provide at least 200LFM airflow for extended
operation at 10A
R22
TB1
U1
U2
U3
T1
SUPPLIER
QTY
0
1
1
1
1
1
_______________________________________________________________________________________
Not installed, resistor (1206)
2 points terminal block (0.2in center)
180W planar transformer
Coilcraft B0860-C
MAX5069AAUE (16-pin TSSOP-EP)
High CTR optocoupler
(ultra-small flat-lead)
NEC PS2911-1-M
0.6V ±0.5% shunt regulator
(SOT23-5)
Maxim MAX8515AEZK-T
DESCRIPTION
Quick Start
631-435-1110
561-752-5000
310-322-3331
619-661-6835
843-946-0238
408-588-2247
847-639-6400
361-992-7900
770-436-1300
847-803-6100
PHONE
—
MAX5069A Evaluation Kit
1) Connect the electronic load (+) terminal to the
2) Connect a voltmeter to the VOUT and SGND termi-
3) Connect the positive terminal of a 36V to 72V power
4) Turn on the electronic load and set it for “current
5) Turn on the power supply above 36V and verify that
6) Verify that the electronic load is drawing the appro-
DESIGNATION
VOUT, SGND
843-626-3123
408-588-2213
631-435-1824
847-639-1469
561-742-1178
310-726-8721
361-992-3377
770-436-3030
619-661-1055
847-390-4405
VOUT banana jack. Connect the electronic load (-)
terminal to the SGND banana jack.
nals to measure the output voltage.
supply to the +VIN terminal (TB1-1). Connect the
power supply’s ground to the -VIN terminal (TB1-2).
mode” and up to 5A of current.
the voltmeter reads +12V normally.
priate current.
None
None
None
None
None
None
None
FAX
—
Component List (continued)
QTY
2
4
2
1
1
1
1
1
www.avxcorp.com
www.cel.com
www.centralsemi.com
www.coilcraft.com
www.cooperet.com
www.irf.com
www.irctt.com
www.murata.com
www.sanyodevice.com
www.component.tdk.com
www.vishay.com
Component Suppliers
Uninsulated banana jacks
Rubber bumpers
Zinc-plated metal screws, 4-40 x 1/4
Nylon hex nut 4-40
Nylon screw 4-40 x 3/8
TO-220 thermally conductive
insulating pad
TO-220AB aluminum heatsink
(10.4°C/W)
MAX5069 PC board
DC-DC Converter Output
DESCRIPTION
WEBSITE
3