AC03TBR22J ABCO Electronics, AC03TBR22J Datasheet - Page 12

• Manufacturer Part Number: AC03TBR22J
• Description: Leaded Inductors
• Manufacturer: ABCO Electronics

RELIABILITY
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before your order and/or use.
1. Operating Temperature
2. Storage Temperature
3. Q
4. Self Resonant Frequency
5. DC Resistance
6. DC Bias Characteristics
7. Temperature Char-
8. Inductance
9. Rated Current
10.Terminal
11. Body Strength
12. Resistance to vibration
13. Resistance to Shock
14. Solderability
15. Resistance to
Range
Range
acteristics
Soldering Heat
Strength
Item
Tensile
Bending
-25 ~ +85˚C
-40 ~ +85˚C
Within the specified tolerance
Within the specified tolerance
Within the specified tolerance
∆L/L → Within -10%
∆L/L → Within
Within the Specified tolerance
Within the specified tolerance
No abnormality such as cutoff or looseness of lead
No abnormality such as cutoff or looseness of lead
No abnormality such as damage
∆L/L → Within
Q → 30 min.
No significant
abnormality in
appearance
At least 75% of terminal electrode is covered by new solder
No significant
abnormality in
appearance
AL02, AL03 Type
±
±
5%
5%
∆L/L → Within
Q/Q → Within
No significant
abnormality in
appearance
No significant
abnormality in
appearance
Specified Value
AL04 Type
±
±
10%
5%
∆L/L → Within
Q → 15 min.
No significant
abnormality in
appearance
∆L/L → Within
Q → 15 min.
AL05 Type
±
±
5%
5%
Including self-generated heat.
Measuring equipment: LCR meter(HP4285A + 42851A or its equivalent)
Measuring frequency: Specified frequency
Measuring equipment:
(Dip meter or its equivalent)
Measuring equipment: m+J80 Ω Hi Tester(3226 or its equivalent)
Measure inductance with application of rated current using
LCR meter to compare it with the initial value.
Change of maximum inductance deviation in step 1 to 5
Measuring equipment: LCR meter (HP4285A+42851A or its equivalent)
Measuring frequency: Specified frequency
The maximum DC value having inductance decrease within 10%
and temperature increase within 20˚C by the application of DC bias
Apply the stated tensile force progressively in the direction
to draw terminal
Suspend a mass at the terminal, incline the body through angle of 90˚
and return it to intial position is This operation is done over a period of
2~3 sec. Then a second bend in the opposite direction shall be made.
Number of bends: Two times
AL02
Applied force: 30N
Duration: 10 sec.
Speed: Shall attain to specified force in 2 sec.
AL03, 04, 05
Applied force: 50N
Duration: 10 sec.
Speed: Shall attain to specified force in 2 sec.
According to JIS C 5102 clause 8.2
Vibration type: A
Duration: 2 hrs each in X, Y and Z directions Total: 6 hrs
Frequency range: 10 to 55 to 10 Hz(1min.)
Amplitude: 1.5 mm
Mountiong method: Soldering onto printed board
Recovery: At least 1 hr of recovery under the standard condition
after the test, followed by the measurement within 2 hrs.
Drop test
impact materal: Concrete of vinyl tile
Height: 1m
Total number of drops: 10 times
Solder temperature: 230
Duration: 3
Solder temperature: 270
Duration: 5
Immersed conditions: inserted into substrate with t = 1.6 mm
Recovery: At least 1 hr of recovery under the standard condition
after the test, followed by the measurement within 2 hrs.
Nominal wire diameter(mm) Tensile force(N)
Nominal wire diameter(mm) Bending force(N) Mass weight(kg)
0.43＜
0.3＜
0.5＜
Step
1
2
3
4
5
±
±
ø
ø
ø
0.5 sec.
0.5 sec.
d
d
d
≤
≤
≤
Test Methods and Remarks
0.65
0.5
0.8
+85 (Maximum operating temperature)
-25 (Minimum operating temperature)
20
20 (Reference temperature)
20
±
±
5˚C
5˚C
Temperature(˚C)
2.5
25
5
Duration(S)
0.25
0.5
5
55