LPC2210 Philips Semiconductors (Acquired by NXP), LPC2210 Datasheet - Page 29

• Manufacturer Part Number: LPC2210
• Description: 16/32-bit Arm Microcontroller; With 10-bit ADC And External Memory Interfacethe LPC2210 is Based on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support. For Critical Code Size Applications, The Alternative 16-bit Thumb Mo
• Manufacturer: Philips Semiconductors (Acquired by NXP)

Philips Semiconductors
Table 10:
T
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Table 11:
V
4.5 MHz.
[1]
[2]
[3]
[4]
[5]
9397 750 12872
Preliminary data
Symbol Parameter
R
I
V
V
V
V
I
Oscillator pins
Symbol
AV
C
DL
IL
OS
G
A
2
lkg
amb
3A
C pins
IH
IL
hys
OL
e
PDB
IN
e
e
IN
e
e
= 2.5 V to 3.6 V unless otherwise specified; T
Typical ratings are not guaranteed. The values listed are at room temperature (+25 ˚C), nominal supply voltages.
Pin capacitance is characterized but not tested.
Including voltage on outputs in 3-state mode.
V
3-state outputs go into 3-state mode when V
Accounts for 100 mV voltage drop in all supply lines.
Only allowed for a short time period.
Minimum condition for V
Conditions: V
The A/D is monotonic, there are no missing codes.
The differential non-linearity (DLe) is the difference between the actual step width and the ideal step width. See
The integral no-linearity (ILe) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See
The offset error (OSe) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See
= 40 C to +85 C for commercial, unless otherwise specified.
3
supply voltages must be present.
Pull-down boot resistor on
BOOT1:0 pins for system
configuration selection
High level input voltage
Low level input voltage
Hysteresis voltage
Low level output voltage
Input leakage to V
X1 input Voltages
X2 output Voltages
Static characteristics
A/D converter DC electrical characteristics
SSA
Parameter
Analog input voltage
Analog input capacitance
Differential non-linearity
Integral non-linearity
Offset error
Gain error
Absolute error
Figure
= 0 V, V
4.
i
= 4.5 V, maximum condition for V
3A
[1][6]
SS
[1][5]
= 3.3 V.
[1][7]
[6]
…continued
[1][4]
Conditions
unloaded data bus lines D26 and/or
D27
data bus lines D26 and/or D27 are
loaded with external memory and/or
memory mapped I/Os leaking total
additional current I
V
V
V
I
V
V
[1][2][3]
OL
TOL
TOL
TOL
i
i
= V
= 5 V
3
= 3 mA
is grounded.
is from 4.5 V to 5.5 V
is from 4.5 V to 5.5 V
is from 4.5 V to 5.5 V
3
amb
Rev. 01 — 09 February 2004
16/32-bit ARM microcontrollers with external memory interface
Figure
= 40 C to +85 C unless otherwise specified; A/D converter frequency
i
= 5.5 V.
4.
lkgt
Min
0
-
-
-
-
-
-
Min
-
-
0.7 V
-
-
-
-
-
0
0
TOL
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Max
V
1
Typ
10
-
-
-
0.5 V
-
2
10
-
-
1
2
3
0.5
4
3A
[1]
TOL
LPC2210
Figure
Max
-
-
0.3 V
-
0.4
4
22
V
V
----------------------------- -
70 A
18
18
0.7V
Unit
V
pF
LSB
LSB
LSB
%
LSB
4.
TOL
+
l
lkgt
29 of 39
Unit
k
V
V
V
V
A
A