MAX649 Maxim, MAX649 Datasheet - Page 12

• Manufacturer Part Number: MAX649
• Description: 5V/3.3V/3V or Adjustable / High-Efficiency /
• Manufacturer: Maxim

5V/3.3V/3V or Adjustable, High-Efficiency,
Low I
a drain-to-source rating of -20V and a typical on-resis-
tance of 0.115Ω at 2A with V
list suppliers of switching transistors suitable for use
with these devices.
The primary criterion for selecting the output filter
capacitor is low equivalent series resistance (ESR),
rather than high capacitance. An electrolytic capacitor
with low enough ESR will automatically have high
enough capacitance. The product of the inductor-cur-
rent variation and the ESR of the output filter capacitor
determines the amplitude of the high-frequency ripple
seen on the output voltage. When a 330µF, 10V
Sprague surface-mount capacitor (595D series) with
ESR = 0.15 is used, 40mV of output ripple is typically
observed when stepping down from 10V to 5V at 1A.
The output filter capacitor's ESR also affects efficiency.
Use low-ESR capacitors for best performance. The
smallest low-ESR SMT tantalum capacitors currently
available are from the Sprague 595D series. Sanyo OS-
CON organic semiconductor through-hole capacitors
and the Nichicon PL series also exhibit very low ESR.
Table 1 lists some suppliers of low-ESR capacitors.
The input bypass capacitor reduces peak currents
drawn from the voltage source, and also reduces the
Table 1. Component Selection Guide
12
Surface Mount
Miniature
Through-Hole
Low-Cost
Through-Hole
PRODUCTION
______________________________________________________________________________________
METHOD
Q
, Step-Down DC-DC Controllers
Sumida
CDR125-220 (22µH)
Coiltronics
CTX 100 series
Sumida
RCH855-220M
Renco
RL 1284-22
INDUCTORS
GS
Capacitor Selection
Input Bypass Capacitor
Output Filter Capacitor
= -4.5V. Tables 1 and 2
Matsuo
267 series
Sprague
595D series
Sanyo
OS-CON series
low-ESR organic
semiconductor
Nichicon
PL series
low-ESR electrolytics
United Chemi-Con
LXF series
CAPACITORS
Nihon
NSQ series
Motorola
1N5820,
1N5823
amount of noise at the voltage source caused by the
switching action of the MAX649/MAX651/MAX652.
The input voltage source impedance determines the
size of the capacitor required at the V+ input. As
with the output filter capacitor, a low-ESR capacitor
is recommended. Bypass the IC separately with a
0.1µF ceramic capacitor placed close to the V+ and
GND pins.
Bypass REF with a 0.1µF or larger capacitor. REF can
source at least 100µA.
Proper PC board layout is essential because of high
current levels and fast switching waveforms that radiate
noise. Minimize ground noise by connecting the anode
of the catch diode, the input bypass capacitor ground
lead, and the output filter capacitor ground lead to a
single point (“star” ground configuration). A ground
plane is recommended. Also minimize lead lengths to
reduce stray capacitance, trace resistance, and radiat-
ed noise. In particular, the traces connected to FB (if an
external resistor divider is used) and EXT must be
short. Place the 0.1µF ceramic bypass capacitor as
close as possible to V+ and GND.
DIODES
IRC
LRC series
IRC
OAR series
CURRENT-SENSE
RESISTORS
Layout Considerations
Siliconix
Little Foot series
Motorola
medium-power
surface-mount products
Motorola
Motorola
TMOS power MOSFETs
Reference Capacitor
MOSFETS