MAX8588 Maxim Integrated Products, MAX8588 Datasheet - Page 20

• Manufacturer Part Number: MAX8588
• Description: High-Efficiency Low-IQ PMIC
• Manufacturer: Maxim Integrated Products

High-Efficiency, Low-I
Dynamic Core for PDAs and Smartphones
When the input voltage is below 2.35V (typ), an under-
voltage-lockout (UVLO) circuit disables the IC. The
inputs remain high impedance while in UVLO, reducing
battery load under this condition. All serial registers are
maintained with the input voltage down to at least 2.35V.
The reset output (RSO) is low when the MR input is low
or when V7 is below 2.425V. V7 is powered from V1
(when enabled) or the backup-battery input (BKBT).
RSO normally goes low:
1) When power is first applied in configurations with no
2) When power is removed in configurations with no
3) If the backup battery falls below 2.425V when V1 is
4) When the manual reset button is pressed (MR goes
If V
for 65ms after V7 rises above 2.3V. However, if V
2.4V when V7 exceeds 2.3V, or if V
same time, RSO deasserts immediately with no 65ms
delay. There is no delay in the second case because the
timer circuitry is deactivated to minimize operating cur-
rent during V
If it is desired to have a 65ms RSO release delay for any
sequence of V
used. An RC connected from IN to MR delays the rise of
MR until after V
either sequence of V7 and V
65ms after both are up. The only regulator output that
affects RSO is V7. RSO will not respond to V1–V6, which
are monitored by POK. Also, RSO is high impedance
and does not function if BKBT is not powered.
MR is a manual reset input for hardware reset. A low
input at MR causes the RSO output to go low for at least
65ms and also resets the V3 output to its default 1.3V set-
ting and turns off the V6 output. MR impacts no other
MAX8588 functions.
The DBI and LBI inputs monitor input power (usually a
battery) and trigger the DBO and LBO outputs. The
dead-battery comparator triggers DBO when the battery
20
separate backup battery (external diode from IN to
BKBT).
separate backup battery (external diode from IN to
BKBT).
off or out of regulation.
low).
IN
______________________________________________________________________________________
> 2.4V, an internal timer delays the release of RSO
IN
Undervoltage-Lockout Functions
IN
undervoltage lockout.
IN
Low-Battery Comparators—DBI, LBI
and V7, the circuit in Figure 2 may be
powers up. The 65ms timer is valid for
Voltage Monitors, Reset, and
Reset Output (RSO) and MR Input
IN
and does not release until
Undervoltage Lockout
IN
Dead-Battery and
and V7 rise at the
IN
Q
<
PMIC with
(V
factory-set 3.15V threshold is selected by connecting
DBI to IN, or the threshold can be programmed with a
resistor-divider at DBI. The low-battery comparator has
a factory-set 3.6V threshold that is selected by connect-
ing LBI to IN, or its threshold can be programmed with a
resistor-divider at LBI.
One three-resistor-divider can set both DBI and LBI
(R1, R2, and R3 in Figure 3) according to the following
equations:
1) Choose R3 to be less than 250kΩ
2) R1 = R3 V
3) R2 = R3 (1.232 x (V
where V
dead-battery threshold.
Figure 3. Setting the Low-Battery and Dead-Battery Thresholds
with One Resistor Chain. The values shown set a DBI threshold
of 3.3V and an LBI threshold of 3.5V (no resistors are needed
for the factory preset thresholds).
Figure 2. An RC delay connected from IN to MR ensures that
the 65ms RSO release delay remains in effect for any
sequence of IN and V7.
IN
) discharges to the dead-battery threshold. The
MAIN BATTERY
LB
is the low-battery threshold and V
438kΩ
200kΩ
62kΩ
LB
0.22µF
100kΩ
R1
R2
R3
(1 - (1.232 / V
IN
DBI (1.232V THRESHOLD)
LBI (1.00V THRESHOLD)
LB
IN
MR
/ V
MAX8588
DB
DB
MAX8588
) - 1)
))
www.DataSheet4U.com
DB
is the