CMM3566-LC Celeritek, CMM3566-LC Datasheet

no-image

CMM3566-LC

Manufacturer Part Number
CMM3566-LC
Description
Ism Band RF ic Products, 3.45-3.5 GHZ
Manufacturer
Celeritek
Datasheet
Preliminary Product Information
November 2000
Features
❏ 7.0V Bias Voltage
❏ +24 dBm Linear Output Power (W-CDMA)
❏ 30 dB Gain at Operating Output
❏ Tested Under Digital Modulation (W-CDMA)
❏ Leadless Chip Carrier (LCC) Package
Applications
❏ Wireless Local Loop Subscriber Units
❏ Wireless Local Loop Base Stations
Description
power amplifier intended for use in PCS handsets and wireless
local loop subscriber units and base stations. The amplifier is
biased to meet the requirements of linear modulation systems
of W-CDMA.
Absolute Maximum Ratings
* Max (+V d ) and (-V g ) under linear operation. Max potential difference across the device at 1dB gain compression point (2V d + |-V g |) not to exceed the minimum breakdown voltage (BV GD ) of +18V.
Recommended Operating Conditions
Application Information
positive and a negative supply voltages for proper operation. It is
essential when turning on the device that the negative supply be
applied before the positive supply. When turning the device off,
the positive supply should be removed before the negative supply
is removed.
voltages and bias currents. It is important that the maximum power
dissipation specification for the package be observed at all times
and that the maximum voltage across the device not be exceeded.
Circuit Design Considerations
Biasing Three negative voltages are needed to set the bias current
of the 3-stage GaAs FET power amplifier. The first stage bias is
controlled via Vg1. The second stage bias is controlled via Vg2.
The output stage is controlled via Vg3. The recommended divider
networks for each gate bias shown in the schematic. The positive
3236 Scott Boulevard
Parameter
Drain Voltage (+V d )
Drain Current (I d )
RF Input Power
DC Gate Voltage (-V g )
Parameter
Drain Voltage (+V d )
The CMM3566-LC is a three stage amplifier that requires a
The CMM3566-LC can be operated over a range of supply
The CMM3566-LC is a 7.0 V, +24 dBm, linear
Rating
+8 V*
1.0 A
0 dBm*
-4.0 V*
Santa Clara, California 95054
Parameter
Power Dissipation
Thermal Resistance
Storage Temperature
BV GD
Typ
7.0
(1 of 4)
Units
Volts
Rating
5 W
20°C/W
-65°C to +150°C
18 V
efficient, power package that provides excellent electrical sta-
bility and low thermal resistance. The part requires minimal
external circuitry for bias and matching to reduce space and
cost.
supply voltage is applied to pins 5, 6, 7 and 8. The negative volt-
age supplies control the quiescent current of the device. The quies-
cent current needs to be set at the level specified in order to get the
guaranteed RF performances.
the output power and the operating current during operation of the
device.
Matching Circuits Output matching circuit is required to achieve
the output power and gain guaranteed. Celeritek’s recommenda-
tion for the topology of the matching circuit is shown in the
schematic diagram of the test circuit in this data sheet.
important to provide adequate de-coupling between the RF signal
and the DC voltages. Inadequate de-coupling could result in low
output power, low gain or oscillation. Celeritek recommends the
bias circuits shown in the evaluation circuit .
W-CDMA Power Amplifier
Parameter
Operating Temperature (PC Board)
Negative bias voltages can also be used to control the gain,
In providing both the negative and positive bias voltages, it is
Phone: (408) 986-5060
The CMM3566-LC is packaged in a low-cost, space
RF IN 4
V g2 2
V g3 1
V g1 3
Functional Block Diagram
Parameter
Operating Temperature
Channel Temperature
Soldering Temperature
– Continued on Page 2 –
3.45 to 3.5 GHz
CMM3566-LC
7.0V, +24 dBm
Ground Tab
Ground Tab
8 RF OUT/+V d3
6 V d2
7 RF OUT/+V d3
5 V d1
Typ
-40 to +70
Fax: (408) 986-5095
Rating
-30°C to +90°C
150°C
240°C for 5 Sec.
Units
°C

Related parts for CMM3566-LC

Related keywords