ADS826E(1) Burr-Brown Corporation, ADS826E(1) Datasheet - Page 2

• Manufacturer Part Number: ADS826E(1)
• Description: 10-Bit/ 60MHz Sampling ANALOG-TO-DIGITAL CONVERTER
• Manufacturer: Burr-Brown Corporation

ELECTRICAL CHARACTERISTICS
At T
2
PACKAGE/ORDERING INFORMATION
NOTE: (1) Fot the most current specifications and package information, refer to our web site at www.ti.com. (2) Models with a slash (/) are available only in Tape
and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces of ADS823E/1K” will get a single 1000-piece Tape and Reel.
This integrated circuit can be damaged by ESD. Texas Instru-
ments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
RESOLUTION
SPECIFIED TEMPERATURE RANGE
ANALOG INPUT
Standard Single-Ended Input Range
Optional Single-Ended Input Range
Common-Mode Voltage
Optional Differential Input Range
Analog Input Bias Current
Input Impedance
Track-Mode Input Bandwidth
CONVERSION CHARACTERISTICS
Sample Rate
Data Latency
DYNAMIC CHARACTERISTICS
Differential Linearity Error (largest code error)
No Missing Codes
Integral Nonlinearity Error, f = 1MHz
Spurious-Free Dynamic Range
2-Tone Intermodulation Distortion
Signal-to-Noise Ratio (SNR)
Signal-to-(Noise + Distortion) (SINAD)
Effective Number of Bits
Output Noise
Aperture Delay Time
Aperture Jitter
Over Voltage Recovery Time
Full-Scale Step Acquisition Time
PRODUCT
ADS823E
ADS826E
f = 1MHz
f = 10MHz
f = 1MHz
f = 10MHz
f = 9.5MHz and 9.9MHz (–7dB each tone)
f = 1MHz
f = 10MHz
f = 1MHz
f = 10MHz
A
= full specified temperature range, V
"
"
ELECTROSTATIC
DISCHARGE SENSITIVITY
(5)
, f = 1MHz
(5)
(2)
PACKAGE-LEAD
(4)
SSOP-28
SSOP-28
"
"
S
= +5V single-ended input range = 1.5V to 3.5V, sampling rate = 60MHz, external reference, unless otherwise noted.
Referred to Full-Scale Sinewave
Referred to Full-Scale Sinewave
Input Grounded
DESIGNATOR
–3dBFS Input
Ambient Air
PACKAGE
2Vp-p
1Vp-p
2Vp-p
DB
DB
"
"
(1)
www.ti.com
TEMPERATURE
–40 C to +85 C
–40 C to +85 C
SPECIFIED
RANGE
MIN
10k
1.5
67
57
56
2
2
"
"
EVALUATION MODULE ORDERING INFORMATION
ABSOLUTE MAXIMUM RATINGS
NOTE: (1) Stresses beyond those listed under "absolute maximum ratings" may cause
permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated under
"recommended operating conditions" is not implied. Exposure to absolute-maximum-
rated conditions of extended periods may affect device reliability.
+V
Analog Input ............................................................. –0.3V to (+V
Logic Input ............................................................... –0.3V to (+V
Case Temperature ......................................................................... +100 C
Junction Temperature .................................................................... +150 C
Storage Temperature ..................................................................... +150 C
PRODUCT
ADS823E
S
–40 to +85
ADS823E
10 Tested
1.25 || 5
....................................................................................................... +6V
Tested
TYP
300
2.5
0.25
0.25
9.5
0.2
1.2
74
74
64
60
60
59
59
0.5
1
5
3
2
5
PACKAGE
MARKING
ADS823E
ADS826E
MAX
60M
3.5
1.0
2.0
3
3
"
"
MIN
65
56
55
ADS823E/1K
ADS826E/1K
ORDERING
NUMBER
ADS823E
ADS826E
ADS826E
–40 to +85
10 Tested
Tested
TYP
73
73
59
59
58
58
EVALUATION MODULE
ADS823, ADS826
(1)
(1)
(1)
DEM-ADS823E
Tape and Reel, 1000
Tape and Reel, 1000
MAX
MEDIA, QUANTITY
SBAS070B
TRANSPORT
Rails
Rails
Samples/s
LSBs rms
M || pF
Clk Cyc
dBFS
S
S
ps rms
UNITS
dBFS
LSBs
MHz
LSB
LSB
Bits
dBc
Bits
+ 0.3V)
+ 0.3V)
dB
dB
dB
dB
ns
ns
ns
V
V
V
V
C
A
(3)