STK415-120-E Sanyo Semicon Device, STK415-120-E Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
STK415-120-E
Manufacturer Part Number
STK415-120-E
Description
2-Channel Power Switching Audio Power IC
Manufacturer
Sanyo Semicon Device
Datasheet
1.STK415-120-E.pdf
(12 pages)
GND
+V H
STK415-100 Series BTL Application
+V L
-V H
-V L
100μF
100μF
/50V
/50V
100μF
100μF
/100V
/100V
This catalog provides information as of July 2009. Specifications and information herein are subject
to change without notice.
60V
/3A
+V L
1
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
60V
/3A
-V L
2
15V
15V
+OFF
SET
3
100Ω/
1W
-OFF
SET
4
-Pre
5
-V H
6
STK415-100 series
+V H OUT
100μF
100μF
/100V
/100V
7
100Ω/
1W
Ch1+
8
Ch1-
OUT
9
56kΩ
3pF
Ch2+
OUT
10 11 12 13 14
OUT
Ch2-
56kΩ
3pF
+Pre
SUB
STK415-120-E
GND IN
Ch1
15 16 17 18
100
pF
Ch1
NF
22μF
/10V
560Ω
ST-
BY
Ch2
NF
22μF
560Ω
/10V
56kΩ
33μF
33μF
Ch2
19
IN
(*1) The voltage applied to the Stand-by pin (#17) must not
exceed the maximum rated value (VST max).
4.7Ω
4.7Ω
3μH
3μH
2.2μF
/50V
R30 (*1)
1kΩ
4.7Ω/1W
4.7Ω/1W
0.1μF
0.1μF
Ch2 OUT
Ch1 OUT
www.DataSheet4U.com
GND
Stand-By Control
Voltage VST
GND
Ch1 IN
PS
No. A1502-12/12
R L =8Ω