MT29F8G08FABWP Micron Technology, Inc, MT29F8G08FABWP Datasheet - Page 32
![no-image](/images/no-image-200.jpg)
MT29F8G08FABWP
Manufacturer Part Number
MT29F8G08FABWP
Description
Manufacturer
Micron Technology, Inc
Datasheet
1.MT29F8G08FABWP.pdf
(59 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT29F8G08FABWP
Manufacturer:
MICRON
Quantity:
10
PROGRAM PAGE CACHE MODE 80h–15h
Figure 24:
09005aef818a56a7 pdf/ 09005aef81590bdd source
2gb_nand_m29b__2.fm - Rev. H 9/05 EN
PROGRAM PAGE CACHE MODE Example
Notes: 1. See Note 3, Table 19 on page 44.
Cache programming is actually a buffered programming mode of the standard PAGE
PROGRAM command. Programming is started by loading the SERIAL DATA INPUT
(80h) command to the command register, followed by five cycles of address, and a full or
partial page of data. The data is initially copied into the cache register, and the CACHE
WRITE (15h) command is then latched to the command register. Data is transferred
from the cache register to the data register on the rising edge of WE#. R/B# goes LOW
during this transfer time. After the data has been copied into the data register and R/B#
returns to HIGH, memory array programming begins.
When R/B# returns to HIGH, new data can be written to the cache register by issuing
another CACHE PROGRAM command sequence. The time that R/B# stays LOW will be
controlled by the actual programming time. The first time through equals the time it
takes to transfer the cache register contents to the data register. On the second and sub-
sequent programming passes, transfer from the cache register to the data register is held
off until current data register content has been programmed into the array.
Bit 6 (Cache R/B#) of the status register can be read by issuing the READ STATUS (70h)
command to determine when the cache register is ready to accept new data. The R/B#
pin always follows bit 6.
Bit 5 (R/B#) of the status register can be polled to determine when the actual program-
ming of the array is complete for the current programming cycle.
If just the R/B# pin is used to determine programming completion, the last page of the
program sequence must use the PROGRAM PAGE (10h) command instead of the
CACHE PROGRAM (15h) command. If the CACHE PROGRAM (15h) command is used
every time, including the last page of the programming sequence, status register bit 5
must be used to determine when programming is complete. (See Figure 24.)
Bit 0 of the status register returns the pass/fail for the previous page when bit 6 of the
status register is a “1” (ready state). The pass/fail status of the current PROGRAM opera-
tion is returned with bit 0 of the status register when bit 5 of the status register is a “1”
(ready state). (See Figure 24.)
R/B#
R/B#
I/Ox
I/Ox
2. Check I/O[6:5] for internal Ready/Busy. Check I/O[1:0] for pass fail. RE# can stay LOW or
pulse multiple times after a 70h command.
80h
80h
Data Input
Data Input
Address &
Address &
2, 4, and 8Gb x8/x16 Multiplexed NAND Flash Memory
15h
15h
t CBSY
t CBSY
70h
80h
Status
Output
Data Input
Address &
32
2
A: Without status reads.
80h
B: With status reads.
15h
Data Input
Address &
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t CBSY
80h
10h
Data Input
Address &
t PROG
70h
15h
Output
Status
Command Definitions
t CBSY
2
©2004 Micron Technology, Inc. All rights reserved.
80h
Data Input
Address &
10h
t LPROG
1