ADC1173CIMTC National Semiconductor, ADC1173CIMTC Datasheet - Page 6

• Manufacturer Part Number: ADC1173CIMTC
• Description: 8-Bit/ 3-Volt/ 15MSPS/ 33mW A/D Converter
• Manufacturer: National Semiconductor

www.national.com
Converter Electrical Characteristics
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func-
tional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed speci-
fications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions.
Note 2: All voltages are measured with respect to GND = AV
Note 3: When the input voltage at any pin exceeds the power supplies (that is, less than AV
be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of
25 mA to two.
Note 4: The absolute maximum junction temperatures (T
junction-to-ambient thermal resistance
TSSOP,
this part is 98˚C/W for the EIAJ SOIC). Note that the power dissipation of this device under normal operation will typically be about 49 mW (33 mW quiescent power
+ 13 mW reference ladder power + 3 mW due to 1 TTL loan on each digital output. The values for maximum power dissipation listed above will be reached only when
the ADC1173 is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is re-
versed). Obviously, such conditions should always be avoided.
Note 5: Human body model is 100 pF capacitor discharged through a 1.5k
Note 6: See AN450, Surface Mounting Methods and Their Effect on Product Reliability , or the section entitled Surface Mount found in any post 1986 National
Semiconductor Linear Data Book, for other methods of soldering surface mount devices.
Note 7: The analog inputs are protected as shown below. Input voltage magnitudes up to 6.5V or to 500 mV below GND will not damage this device. However, errors
in the A/D conversion can occur if the input goes above V
be 2.75V
Note 8: To guarantee accuracy, it is required that AV
Note 9: Typical figures are at T
Level).
Note 10: At least two clock cycles must be presented to the ADC1173 after power up. See Section 4.0 for details.
JA
DC
is 92˚C/W, so P
to ensure accurate conversions.
D
MAX = 1,358 mW at 25˚C and 815 mW at the maximum operating ambient temperature of 75˚C. (Typical thermal resistance,
J
= 25˚C, and represent most likely parametric norms. Test limits are guaranteed to National’s AOQL (Average Outgoing Quality
JA
, and the ambient temperature, T
DD
DD
and DV
J
max) for this device is 150˚C. The maximum allowable power dissipation is dictated by T
or below GND by more than 50 mV. As an example, if AV
SS
DD
= DV
be well bypassed. Each supply pin must be decoupled with separate bypass capacitors.
SS
= 0V, unless otherwise specified.
A
, and can be calculated using the formula P
(Continued)
resistor. Machine model is 220 pf discharged through ZERO
6
SS
DS100890-10
or DV
SS
, or greater than AV
DD
is 2.7V
DD
D
MAX = (T
or DV
DC
DD
, the full-scale input voltage must
), the current at that pin should
J
max - T
.
A
)/
JA
. In the 24-pin
J
max, the
JA
, of