PIC16F716 Microchip Technology, PIC16F716 Datasheet - Page 31

• Manufacturer Part Number: PIC16F716
• Description: 8-bit Flash-based Microcontroller with A/D Converter and Enhanced Capture/Compare/PWM
• Manufacturer: Microchip Technology

5.0
The Timer1 module timer/counter has the following
features:
• 16-bit timer/counter
• Readable and writable (Both registers)
• Internal or external clock select
• Interrupt on overflow from FFFFh to 0000h
• Reset from ECCP module trigger
Timer1 has a control register, shown in Register 5-1.
Timer1 can be enabled/disabled by setting/clearing
control bit TMR1ON (T1CON<0>).
Figure 5-1 is a simplified block diagram of the Timer1
module.
Additional information on timer modules is available in
the
(DS33023).
REGISTER 5-1:
 2003 Microchip Technology Inc.
(Two 8-bit registers; TMR1H and TMR1L)
PICmicro
TIMER1 MODULE
bit 7-6
bit 5-4
bit 3
bit 2
bit 1
bit 0
®
Mid-Range
Unimplemented: Read as '0'
T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
T1OSCEN: Timer1 Oscillator Enable Control bit
1 = Oscillator is enabled
0 = Oscillator is shut off
T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS = 1
1 = Do not synchronize external clock input
0 = Synchronize external clock input
TMR1CS = 0
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
TMR1CS: Timer1 Clock Source Select bit
1 = External clock from pin RB1/T1OSO/T1CKI (on the rising edge after the first falling edge)
0 = Internal clock (F
TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
Note 1:
Legend:
R = Readable bit
-n = Value at POR
bit 7
T1CON: TIMER1 CONTROL REGISTER (ADDRESS: 10h)
U-0
—
The oscillator inverter and feedback resistor are turned off to eliminate power drain.
Reference
U-0
—
OSC
(1)
/4)
T1CKPS1 T1CKPS0
Manual,
R/W-0
W = Writable bit
‘1’ = Bit is set
Preliminary
R/W-0
5.1
Timer1 can operate in one of these modes:
• As a timer
• As a synchronous counter
• As an asynchronous counter
The operating mode is determined by the clock select
bit, TMR1CS (T1CON<1>).
In Timer mode, Timer1 increments every instruction
cycle. In Counter mode, it increments on every rising
edge of the external clock input.
When the Timer1 oscillator is enabled (T1OSCEN is
set), the RB2/T1OSI and RB1/T1OSO/T1CKI pins
become inputs. That is, the TRISB<2:1> value is
ignored.
Timer1 also has an internal “Reset input”. This Reset
can be generated by the ECCP module
(Section 7.0 “Enhanced Capture/Compare/PWM
(ECCP) Module”).
T1OSCEN
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
Timer1 Operation
R/W-0
T1SYNC TMR1CS TMR1ON
R/W-0
PIC16F716
x = Bit is unknown
R/W-0
DS41206A-page 29
R/W-0
bit 0