APL5605 Anpec Electronics Corporation, APL5605 Datasheet
APL5605
Related parts for APL5605
APL5605 Summary of contents
Page 1
... Rev. A.1 - Jan., 2008 600mA Linear Regulator for DC Fan Speed Control General Description The APL5605 is a low quiescent current and low dropout linear regulator which is designed to power a DC fan and delivers up to 600mA output current. The output voltage follows the 1.6 times of VSET voltage and typi- cal dropout voltage is only 220mV (typical) at 600mA output current ...
Page 2
... APL5605 Pin Configuration SOP-8 Top View EN 1 VIN 2 VOUT 3 VSET 4 APL5605 Absolute Maximum Ratings Symbol V VIN to GND GND EN V VOUT to GND OUT T Maximum Junction Temperature J P Power Dissipation D T Storage Temperature Range STG T Maximum Lead Temperature (Soldering, 10 sec) SDR Note 1: Stresses beyond the absolute maximum rating may damage the device and exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
... APL5605 Electrical Characteristics Refer to the typical application circuit. V unless otherwise specified. Typical values are at T Symbol Parameter SUPPLY CURRENT I Quiescent Current Q UNDER-VOLTAGE-LOCKOUT (UVLO) VIN UVLO Threshold VIN UVLO Hysteresis OUTPUT VOLTAGE VOUT Voltage / VSET Voltage VOUT Voltage / VSET Voltage VSET pin Current ...
Page 4
... APL5605 Typical Operating Characteristics V =5V, V =2V, V =3.2V SET OUT IN EN Voltage threshold vs. Input Voltage 1.6 1.5 1.4 1.3 1.2 1.1 1 0.9 0.8 3 3.5 4 4.5 5 Input Voltage (V) VSET Voltage vs. Output Voltage 6 I =10mA 5 OUT 0.5 1 1.5 2 VSET Voltage (V) Dropout vs. Junction Temperature 350 V =3.3V OUT 300 I =600mA OUT ...
Page 5
... APL5605 Typical Operating Characteristics (Cont.) V =5V, V =2V, V =3.2V SET OUT IN Quiescent Current vs. Input Voltage 200 I =0mA OUT 160 120 Input Voltage, V Operating Waveforms V =5V, V =2V, V =3.2V SET OUT IN Power SET 2 V OUT ...
Page 6
... APL5605 Operating Waveforms (Cont.) V =5V, V =2V, V =3.2V SET OUT IN Load transient V =5V =3.2V IN SET OUT =2 OUT 1 2 CH1 : V , 100mV/div OUT CH2 : I , 200mV/div OUT Time : 200 s/div Enable OUT 3 I OUT 4 CH1 : V , 2V/div EN CH2 : V ...
Page 7
... APL5605 Operating Waveforms (Cont.) V =5V, V =2V, V =3.2V SET OUT IN Thermal Shutdown OUT 2 I OUT 3 CH1 : V , 5V/div IN CH2 : V , 2V/div OUT CH3 : I , 500mA/div OUT Time : 500ms/div Pin Descriptions Pin No. Name Enable Control Input. Driving the EN high turns on the regulator. Pulling the EN low turns the ...
Page 8
... APL5605 Block Diagram VIN EN VSET Typical Application Circuit OFF Copyright ANPEC Electronics Corp. Rev. A.1 - Jan., 2008 UVLO and Soft-Start Thermal Shutdown APL5605 VIN VSET VOUT GND V 1.6 V OUT SET Current Limit OUT SET and Foldback VOUT ...
Page 9
... GND. The EN is pulled low by an internal resistor. Current Limit The APL5605 provides a current limit circuitry, which monitors the output current and controls P-MOS’ s gate voltage to limit the output current at 700mA. Foldback Current Limit When the output voltage drops below 0 ...
Page 10
... Please place the input capacitors close to the VIN 2. Ceramic capacitors for load must be placed near the load as close as possible 3. To place APL5605 and output capacitors near the load is good for performance. 4. Large current paths, the bold lines in figure 1, must have wide tracks. ...
Page 11
... APL5605 Package Information SOP MIN 0.10 A2 1.25 b 0.31 c 0.17 D 4.80 E 5.80 E1 3. Note: 1. Follow JEDEC MS-012 AA. 2. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side. ...
Page 12
... APL5605 Carrier Tape & Reel Dimensions K0 SECTION A-A Application A H 330.0± 2.00 50 MIN SOP-8 4.0± 0.10 8.0± 0.10 Devices Per Unit Package Type SOP-8 Copyright ANPEC Electronics Corp. Rev. A.1 - Jan., 2008 P0 P2 OD0 A0 OD1 B SECTION B 12.4+2.00 13.0+0.50 1.5 MIN. 20.2 MIN. 12.0± 0.30 1.75± 0.10 -0.00 -0. 1.5+0.10 2.0± 0.05 1 ...
Page 13
... APL5605 Reflow Condition (IR/Convection or VPR Reflow Tsmax Tsmin 25 Reliability Test Program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Classification Reflow Profiles Profile Feature Average ramp-up rate ( Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) ...
Page 14
... APL5605 Classification Reflow Profiles (Cont.) Table 1. SnPb Eutectic Process – Package Peak Reflow Temperatures Package Thickness <2.5 mm 2.5 mm Table 2. Pb-free Process – Package Classification Reflow Temperatures Package Thickness <1.6 mm 1.6 mm – 2 Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0 C ...